Find trusted local electricians in Williamstown VIC

Wanting to change lighting in apartment to recessed matte black down lights remove wall light Add ceiling fan to master bedroom Add pendant light and wall light Add power extra power point in both bedrooms Change split system

Light will be ordered for you to pick up at your nearest Bunnings Two lights Need you to book the time with the tenant.

3x white downlights and 2x three spotlight black ceiling lights need to be installed.

I need an additional power point installed in my kitchen.

Need someone today to help my crew for rest of today on an AC install Running cables , fit off etc , some duct work

Convert GPO to isolator, isolator provided. Provide certificate.

Need to convert, GPO to isolator for HWS. And certificate provided.

Downright have stopped working. I have 6 in one room that wont turn on. All other rooms work perfectly.

The new DC 102cm fans with lights are to replace existing fans with lights that are in good working order. The new 62mm toggle switches are to replace existing toggle switches which have broken toggles.

install conduit for nbn connection approx 15 metres across a metal roof

I have three electrical jobs that require attention: 1. Garden lights need to be replaced (we can supplier lights) 2. The water system control unit need to be replaces (we have the replacement unit) 3. Pendate light in the kitchen is flickering and needs rewiring.

Looking for an electrician or capable Labourer to help with solar install in williamstown tomorrow and Friday. Price is hourly. Solar experience preferred but not necessary. Price is hourly

Looking for a hand with some electrical /solar work this Thu/Fri and next Monday Installing sub board and solar three story townhouse flat roof have scissor access. Price is hourly

Will be installing solar and sub board on 3 story townhouse, flat roof. Kliplock will have scissor for access. Don’t necessarily need electrician but at least must be good with heights and hand ltools. Big flat roof so not a difficult roof. Price is hourly 3 days work 4-5-8 Dec

We require a licensed electrician to install and connect 3-phase power in our factory for: 1. Light Gauge Steel Roll-Forming Machine (main equipment) 2. Battery-powered Forklift Charger (Lithium) – requires a 3-phase outlet connection from the same supply ⸻ Scope of Works • Run approx. 30 m of 16 mm 4C+E circular orange cable (see photos). • Install 40 mm rigid PVC conduit with 90° bends neatly along wall and ceiling (route shown in red in photo). • Connect to existing main distribution board inside the office area (see photo). • Install and wire: • 1 × 40 A 5-pin 3-phase outlet (IP66) for the roll-forming machine • 1 × 32 A 5-pin 3-phase outlet (IP66) for the forklift charger • Supply and fit appropriate RCBO / MCB protection as per parts list. • Test, label, and commission both outlets for safe operation. • Provide certificate of electrical safety on completion. ⸻ Materials Supplied On-Site • 30 m – 16 mm 4C+E circular unarmoured orange cable • 10 × 40 mm rigid PVC conduits (4 m lengths) • 90° conduit bends • 3-phase outlets and plugs (40 A & 32 A IP66) • Distribution board enclosure and circuit protection devices (see parts list) ⸻ Requirements • Fully licensed A-Grade electrician with industrial experience • Own tools, consumables, and ladders if required • Must provide Certificate of Electrical Safety upon completion. (I will organise scissor lift) ⸻ Photos Attached 1. Factory wall and conduit path (marked in red/blue) 2. Main distribution board location (office) 3. Orange 3-phase cable roll 4. Supplied conduits 5. Parts list with all supplied materials ⸻ Preferred Start: ASAP (factory is ready for works)

Replace four light fittings with led lights Replace three power switches Replace one light switch Insert a new tv point insert a new kitchen power switch Disconnect hardwire oven

Rewiring for a one bedroom apartment, replace light switches and power points.

Replace 3 lights. I have already purchased the lights

Requiring testing and tagging of new equipment of approximately 50 power plugs mostly are Christmas lights one TV and two laptop chargers, and six light fittings for a forthcoming exhibit ( the exhibit is Tomorrow so I urgently need this task done this evening. It’s located in williamstown.) The task is immediately available. Please ensure you’re licensed to do the tagging.

Hi, I have a council inspection tomorrow 8am, and none of my appliances are tested and tagged yet. I need you onsite in the morning to test and tag all my plug-in equipment—around 5-6 items. It needs to be done onsite and ready before the inspector arrives. Can you bring your tester and tags, and possibly provide a short summary report or invoice with your license details?