Find trusted local electricians in Yarraville

We have bought 3 new pendant lights to hang from the roof in 3 different rooms. We need the old lights removed and the new lights installed. Need a licensed electrician please. Message me for any more information you need

Replacement of firealarm x 2 - wired Replacement of downlight x 2 - wired We will provide the firealarm and the downlight

• 1 x Single GPO at height 1800mm in bathroom recess (for dryer) • 1 x Double GPO at 600mm height in bathroom recess (for washing machine) • Replace 5 x old single bedroom/hallway light switches (new switches supplied) • Remove single light switch on wall (near recess) in bathroom

Boiler service needed gas heater in yarraville

Electrician required for for bathroom reno - rough in stage : - remove existing ceiling heater - install plug base for ceiling fan - install plug base for downlight - move one powerpoint within a meter of current location After paint and tiles : - fit off ceiling fan - fit off one down light - fit off switch - fit off PowerPoint

We have just had a verandah with downlights installed. Need to have them connected.

I have 10 x Tuya smart downlights and 1x nanoleaf skylight to install: https://nanoleaf.me/en-au/products/nanoleaf-skylight The downlights will replace existing lights. The skylight will need to be installed. Roof access is via a manhole.

Ceiling fan light not working I have a ceiling fan with an LED light which has stopped working. The fan itself still works fine, but there is no proper illumination from the light. I thought the LED light plate might be the problem, so I bought a replacement and fitted it, but unfortunately that hasn't fixed it. I'm looking for a licensed electrician to have a look, work out what's wrong and repair it if possible. I'd prefer to repair the existing fan rather than replace the whole unit. I already have the replacement LED plate here. Please let me know your approximate cost/call-out fee.

12 down lights to be changed to energy efficient LEDs. Current ones have transformers. Preferably licensed sparky to do the job. Globes to be supplied. Please advise which globes will be installed.

Iv been told the fan needs to be first placed on a piece of wood then go on wall , no electrical work required as the lead just goes into a power point .

Have a vintage light that has been professionally wired by an electrician to be bolted into a ceiling beam and hung over the dining room table. Have the correct bolt to secure it and separate wall switch if required. Need two hardwired halogens swapped over to led plug in lights. The vintage light fitting works perfectly with the new transformer. I just need a sparky that appreciates the effort I’ve gone to in bringing this beautiful old fitting back to life so it can be hung and enjoyed. Halogens an easy no fuss switch. Have costed the job on 2 hours at $100 per hour for the light fitting and 30 mins for the halogens. Would like done tomorrow or early Sunday morning. Located Yarraville Any questions just ask. Thanks

Install 2 led downlights to hallway. Downlight kit will be supplied by us. Must be a licensed electrician and have tools and access ladder. Ceiling is approx 3m height. Floor plan attached. Red crosses are proposed Downlights// green is an existing pendant light location (info only) // purple is the light switch location.

I would like a double PowerPoint installed in my bathroom can go under the light switch

Change over existing hanging light fittings for new same.

Install a hard wired fire alarm , install a ceiling fan in master bedroom, install a floodlight at front of house , move a light fitting from master bedroom to other bedroom

We have 4 small single light switches and 4 fan control switches that we would like to change to new covers. We will supply the covers so this job is for labour only. Lanour will include removal of old switch, replace with new, test it’s working. Any patching and painting will be done by others.

Relocate three light switches to nearby wall.

Power point for motorised outdoor blinds- location photo 2 near blind plugs.Conduit to run along top of window and down the corner photo3. Hopefully it can be connected through the weatherboard and connected to existing powerpoint - in corner of photo 1.

Two power points needed, one at the front of the house (inside) and another behind a mounted tv. Double story house but both points are on the ground floor. Tv mount point is directly above an existing power point, the point at the front of the house is backing onto the fuse box and quite close to an existing power point as well

1.Relocate GPO to be a minimum of 500mm from the internal rim of the sink and 1m above the sink. 2. Relocate GPO/DGPO or Switch to be a minimum of 600mm from the edge of the Bath 3. Supply and Fit 20A Circuit Breaker/RCD Combo ( grey one) 4. Supply and Fit 10A Circuit Breaker/RCD Combo ( orange one need safety button on switch)