Find experienced local carpenters in South Melbourne

Storage cabinets in toy room, one bedroom cupboard and a built in desk

Finish carpenter to re install existing skirt boards and arc to plaster over blockwork or plaster over pine framing. (with appropriate gun nailer) Approx 25 l m. of skirt and 20 l m. of arc. Second image shows existing skirts ready for re installation. They were carefully removed in order to reinstall. (They have been denailed.)

In our restaurant that has extention at the back with stump, we just got in last year feb25 and found out some wood damaged by termites. The termite has been gone. We need help to replace the damaged stump under. Looking carpenter that passion about the job & can help us with budget. Need a proper quote as we have experienced bad tradie in the past Addrs 179 Clarendon st, south melbourne.

Seeking joiner who can use our GoCabinets flatpack account to create shop drawings, finalise design, order custom joinery in flat pack and then install. Labour only required. We will provide all material.

Hi team, open to offers + suggestions We have a wooden bar that has chipped away at the base and the top - we would like to get a sturdy kick line on it in and get the top painted or add laminate so we don`t have to keep repainting after use. We would also like the white paint freshened up please Can be fixed at our storage unit or taken away and returned - we need it complete by the 2nd of December

Need someone to build me a plywood bed frame similar to the reference pics, just without a bedhead. Ideally a quote with your plywood and cost with just labour/hand if possible.

We have retail store in south Melbourne, and wanted few cabinet for our counter. Can meet at store to discuss and get dimensions further.

Looking for someone to come and prepare, sand and stain a deck using sikkens products. Probably 3 coats for lasting protection!approximately 6m x 4m area including fence and built in bench seat

Calling all woodworkers/crafts people! I need someone with the woodworking skills (and space) to DIY an Ikea cabinet! It’s a plain pine, small-ish cabinet that needs a brutalist makeover! I have the cabinet and spheres, but no space or tools (and skills) to build it. The cabinet is 80x83x30. I’m flexible on pickup and completion, but sooner rather than later preferred! Shoot me any questions you have! Thanks!

sand down 7 door fronts for our kitchen cabinetry (2 of which are tall pantry sized and the other 5 are shorter) and 4 of which for draws. They are solid timber and we are wanting to sand the top layer so we can stain them with a darker stain. Please also provide separate cost if we were to include staining

Repairs to outdoor timber bench. Need a new bench top cut to size, replace rotten timber beam and repair back leg support bracket

There is a stain and burnt section of carpet which needs to be replaced. We have a roll of the exact same carpet, so can be used to replace the damaged area. The apartment is being sold, so end result needs to good.

I would like to build a couple shelves on either side of the Kallax unit in picture below. Both of them will have a stereo speaker at the bottom. The one on the right hand side will be at the same height as the unit, the one on the left would be about the same height as the Billy bookcase on the left. A cut with a router saw will be needed to accommodate skirting board behind. Accommodation for wires at the back (for amplifier, turntable, etc) will be needed. Would aim to use similarly coloured timber as units in pictures.

Carpenter, or suitably experienced handy person to replace a length of baseboard to match existing profile. Approx. 155cm(L)x7cm(H). Task for labour, and can reimburse the cost of board/material separately with receipt.

I am seeking a quote to stain my grey/worn front and rear covered veranda decks, each being long and narrow approx. 10sqm each - total 20sqm in a merbu/darker stain inc preparatory cleaning. Has raised done head nails.

Build 2 boxes 1.5m x 250mm wide x 200mm high using recycled timber and stained to suit

I am looking for a qualified carpenter who is experienced in the replacement of rotten and deteriorated weatherboards, prior to painting in March including punching/reaffixing nails (if needed), with matching board profile. House is single story with ease of access. My estimate would be no more than 50 lengths,if that, but needs assessment.

In MID December I am wanting to install a new wall oven measuring 895W x 572D x 596H (mm) into the space occupied by the oven in the photos. The new oven will be approximately 30 cm’s wider, and I need the cupboards modified to accommodate the new oven. Ideally, I need a cabinet maker to prepare the space for the existing oven’s removal and to reconfigure the cupboards post the new oven being installed. Cupboards must match existing

We are looking for a professional to remove built-in cabinets from a 4-storey building. Each cabinet is located on a different level and will need to be removed carefully to avoid damage. Requirements: Must have Public Liability Insurance 20mil WorkCover, Professional Indemnity insurance. If you’re experienced, insured, and have the tools and expertise to handle this job, please let us know your availability and provide a quote. We look forward to hearing from you!

Using a single piece of Acacia wood - seeking a woodworking professional to cut, sand and apply a light finish for an L shaped Table Top. The L shaped should be 1.1m on each side with rounded corners. Depth of the table is around 50cm like the posted picture