Find experienced local carpenters in Carlton VIC

I need someone to get rid of the monstera roots that are stuck to the wall and plaster over it

I have a timber window frame in my apartment that has cracked/peeling paint and possible minor wood rot. The window also gets very damp in winter and I recently had a millipede come in, so I want the gaps sealed properly. Scope of work: * Scrape and remove loose/flaking paint on the window frame (inside, possibly small touch outside if accessible) * Fill cracks and any minor damaged timber with wood filler * Seal gaps around the frame and glass with appropriate sealant to prevent moisture and bugs getting in * Optional: light sanding and touch-up paint (white) if included This is a first-floor apartment. Inside access is easy. Outside access may be possible with a ladder but only if safe. Looking for someone experienced with basic carpentry/handyman work, especially timber window repairs. Please bring your own tools and materials.

I have a back external deck that is approx. 5m. x 6.5 m. including two sets of wide stairs. The job is to clean, then sand old layer of stain and sealent (i have a hand sander, but could rent a standing sander for the day if you dont have any equipment)apply stain, and then a sealent ( i have these products) i imagine it will take a full day, could be tuesday, or could be wednesday

Hello i need a cabinet to me made inside my wardrobe on the top. It needs to have a locker as well.

the cabinet door stay missed，need to buy and install

I need a custom desktop furniture craft made. Quite simple, 2 pieces. Good quality dark walnut finish. Have 3d design. Attention to detail required. I can come pick up once complete, or delivered to carlton.

This is an office block with several carpentry problems eg small 1 inch square hole in plasterboard-repair and paint; ; replacement of door frame with new door and closer; replacement of closure in 2 bathroom , install about 60 metres of bird spikes , replace vent in lift. you would need to see the property in Carlton Vic as we would like supply of materials and repair work done.

I'm looking for: 1. A kitchen cabinet assembled. Screws are provided. (See first two pics) 2. A couple of protruding screws cut off inside a cabinet (See second two pics) Requires powertools

Ive dropped a few litres of oil based paint in my carpet roughly spanning 50cm by 50 cm. On a very tight budget, please help us out if you can 😔

Remove middle cabinets to install washing machine may require plumbing electrical and cutting laminate to reach under sink I leave pictures but please contact me once you accept and I say yes

Need a carpenter laborer to give me a hand asap.

It is a wooden cupboard, not that big

A few odd things: 1. Install a 70cm kick board under cupboard 2. Build a small draw above oven and install a small surround between oven and edge of cupboard 3. Aircon duct to be secured / filled in. It’s in an awkward spot above a 236cm wardrobe so aesthetics don’t matter, it just needs the gap enclosed and air vent positioned. There likely to be other odd tasks as well.

Need assistance with custom plywood wardrobe doors. I have an idea of what I want, but there are some complicated aspects when it comes to measurement which I need help with. Task includes: Measuring, cutting and installing plywood wardrobe doors.

Window frames and panels are a little weather worn. The need a good sand and a couple of layers of stain. I can provide the stain. The person will need a very tall extender ladder.

This will be for my apartment located in Carlton. Easy access to parking and huge elevator to my floor. I measured the dimension, please refer the photos. You will need to measure again once your offer accepted. 1 . Open bookshelves with 3 partition and 9 rows of adjustable shelves 2. Low table, with 2 cabinet door. 3. Pantry in washroom, with slim space to keep broom, mop etc 4. Overhead cabinet in washroom. So 3 and 4 should be like connected, like a L shape. Please provide your best quote to cut and install. Nothing to be demolished or removed. Wall is empty at the moment.

We need two copies of a three step block to be constructed. All joints need to be glued and nailed and children will be using them. A clear varnish needs to be applied to the surface. A sturdy material needs to be used.

I need someone to source materials and cut two items: 1. Plywood, 12mm or thicker: cut to 290mm x 780mm 2. White melamine particleboard, 16-18mm thick, cut to 78mm x 880mm (must ensure the melamine doesn’t chip) Drop off in Carlton or I can pick up if within 30mins drive.

Details: I need someone to set up two wooden beam structures on my balcony, similar to the example in the picture. Each structure consists of: • One horizontal beam (6 meters long) • One vertical beam (approximately 3 meters high) Requirements: • Bring two sets of wooden beams (each with a 6m horizontal and a 3m vertical beam). • Bring a cutting saw and tools to adjust the beams if needed. • Securely install both structures. What You Need to Bring: • The wood for both sets. • Tools for cutting and securing the beams. I’ll attach a picture as a reference for how it should look.

I need 2 cabinets for my kitchen. Range hood needs to be replaced as well.