Find experienced local carpenters in Carlton North

Our fridge doors are attached to the cabinet doors with an integration kit..i need to replace the fridge so need to unattach the fridge from the cabinet and remove the current integration kit

I have a timber-framed multi-pane fixed window (French door style) with rot at the base of the frame, both visible from inside and outside at the same corner where the sill meets the jamb. Photos attached showing both sides. Looking for a spliced timber repair (“Dutchman repair”) — cutting out the rotted section and scarfing/splicing in new matching timber, rather than replacing the whole frame. The surrounding timber and glass appear sound; this is localised to one corner. There’s a metal piece visible behind the damaged section — please assess on site to confirm what it is (possibly flashing or a fixing) before confirming quoting, as this may affect the repair approach. Once repaired, I’ll handle painting/sealing myself, so quote for timber repair and make-good only (sanded ready for primer), not full paint finish. Looking for someone with joinery or heritage window restoration experience — not a general handyman, as this needs proper timber-to-timber jointing to hold structurally. Photos of the damage attached (interior and exterior view of same corner).

bottom section of carved leg has broken odd, has a wood plug, have tried to glue ut needs expert in carpentry to hold in place.

We are looking for a skilled tradesperson (Carpenter, Heritage Handyman, or Fireplace Specialist) for two distinct tasks in our Victorian terrace. Task 1: Decommissioning & Removal (Living Room) • Remove: Safely extract an existing Jetmaster unit from the wall. • External Work: Remove the external silver flue/cowl. The exterior penetration must be professionally sealed and weatherproofed (e.g., metal capping or flashing) to ensure it is 100% watertight. • Internal Prep: Fill the internal cavity with high-density insulation (e.g., Rockwool) to prevent drafts and noise. • Finish: Leave the opening ready for a plasterer to board over and skim (no need for you to do the final plastering). Task 2: Ornamental Installation (Second Room) • Insert: Install a Schots Emporium cast iron insert into an existing fireplace opening. Note: This is ornamental only—no gas or wood-burning connection required. • Draft Proofing: Firmly pack the chimney throat with insulation to stop drafts before the insert is fixed. • Mantle: Professionally mount a timber mantle over the insert. We are looking for a clean, secure finish with no visible fixings if possible. Requirements: • Experience working with Victorian-era heritage homes. • Strong focus on weatherproofing for the external flue removal. • Attention to detail regarding the alignment and leveling of the cast iron insert and mantle.

I have a piece of timber I need cut to size, it’s about 15cm wide. That’s literally it

We need someone to cut the legs 40mm shorter on a stainless steel bench top so that it aligns with an older unit next to it. The legs are hollow square profile thin stainless steel

Seeking help remaking 2 damaged drawers (no original drawer available), fixing loose drawer faces on 3 drawers and adding a sliding door set up in front of laundry space (incl. removing current door). Price can be discussed depending on scope of works and required materials. Appreciative of any offers for assistance.

Make a free standing wooden platform approximately the width of a door way that comes out about 60cm and about 15cm high (height of the step). It would be a platform in the living room coming from the corridor. It doesn't have to be flash, just something like e.g. a plywood top but strong to stand on and solid ie doesn't tilt/move etc. I currently have a small platform on bricks. Just want something better and firmer.

I have a three seating chair with some 4 x 2 timber on it to raise it so I can sit down. I need to raise it further so I need to add some more for the two timber and some felt at the bottom to stop it scratching the floor.

Shop Island Counter needs draws and cupboards installed Exisiting cupboard doors and internal shelving removed and replaced with custom ( to be built) door (left) and 3 draws where current cupboard door is (right) New shelving on far right measurements are 189x75 1 x cupboard door ( far left) 3 x draws ( 2 small 1 large) middle 3 x open shelving ( far right)

The window is around 4-5m high and will need to be accessed from a lane with a ladder. I will supply the Cutek timber stain and witches hats etc but do not have a ladder. Estimate this is a 1 hour job with some time to allow for x2 coats. I will be able to supervise the lane while the work is being done.

I have an outdoor table that needs the top replaced as the water proof coating has worn off and it’s no longer suitable to be outside. Happy to pay for the wood separately.

Inspection of timber flooring in Victorian Terrace (pre-1900s) due to suspicion of timber borers.

The kitchen floorboard is damaged and needs replacement. I am looking for someone who could find the exact same floorboard and fix the damage. Price is negotiable, and we will cover the the price of the floorboard, however we are looking for someone who can source and purchase it on our behalf.

Need to be available TODAY. PAY HOURLY. ALL MATERIALS PROVIDED! Carpenter to help with framing internal walls and sheeting ply. Installing doorjams, swinging doors around, basic cabinetry.

Help frame up internal partition walls and sheet up with vj panels. Install door jams with doors. Pls quote day rate - 8hrs.

Need a desk top cut down to a smaller size. Desk is solid timber and currently 2100x900mm Would like it cut down to 1600x600

We installed an ikea kitchen awhile back but ikea failed to send us one panel, which now needs to be installed at the base of the cabinet. We have got the panel and it needs to be sanded back slightly to fit into the spot. We'd like you to buy brackets (and/or whatever else is needed to support the panel, and secure it to the wall), so please factor this into the quote. The wall is solid brick. There are pictures to show the spot where the panel is to fit. Let me know if you have any other questions. Need this done by Wednesday at the latest, but would prefer to get it done tomorrow or Tuesday. - Due date: Before Wednesday, 29 November 2023

Hello! We’re wanting to please have a bench top built out of treated plywood for our outdoor bbq. We will be tiling over the top of it. Will need to have a 1cm overhang. Dimensions approx 1970 x 870 x 100 high - Due date: Before Monday, 16 October 2023

Stained wooden floor from a treadmill, need 4 small small square stains removed. - Due date: Before Tuesday, 25 July 2023