Find a reliable appliance technician in Glen Huntly

My fireplace is a Heat & Glo, and sometimes it lights up while other times it doesn’t. I’m hoping someone can help repair it so it works properly.

4 tiles to be installed. Rangehood was raised and has left a gap

Viofo a329 2ch with hardwire kit. Need to hardwire install front and back for a Porsche Cayenne. Ideally have it done today or tomorrow. Located in Glen Huntly

Washing machine has a small leak - task is to review, - taps - seals - hoses to see if leak can be determined. Will need to move machine away from wall to review the above. If determined one of the above, assistance with fixing, if feasible. Handyperson skills needed, keen eye for detail, experience similar jobs. Thanks.

We have an existing gas cooktop that we want to replace. The current cooktop is a 85cm * 50cm, 6 burner gas cooktop mounted on top of a marble kitchen bench. I’ve attached the current setup below. The new one we are trying to install is a SMEG gas + electric cooktop, item number SAIG3953B. Size of which is 90 *50cm. We would like to get an inspection and a quote for the job. For the inspection, we would like to know the following. 1, do you need to cut further on the marble bench in order to fit the new cooktop, and how much does it cost. 2, do you need to rewire the current electrical circuit and how much dues it cost. 3, how much for the installation. Please send your approach and make an offer. Thanks in advance

Disconnect a dishwasher which is under the bench. No need to dispose of as I’m having it removed

The wachine machine is Seiki Washer/Dryer Combo. It has a FE/PE error that needs to be fixed

Have cleaned the oven and have put back the side oven racks, however not correctly, as can't slide the oven trays back in. Need assistance with fitting the side oven racks back correctly so the oven trays can slide in okay. Need to have good handyperson skills. Probably needs to be completed during daylight hours, so you can see easily where oven side racks lineup at back of oven. Thanks.

Doesn’t move with full load, but if load rescued to a couple of wet clothes it runs ok, sometimes need to stop - start couple of times. After a few minutes we can add more clothes and then runs with full Load. Possibly motor issue, but not sure.

F11 error shown on the dishwasher

Bosch washing machine error e-36 error. Have tried to empty but can’t find anything

Looking to install a new induction stove. Mains may require upgrade.

My dryer isn’t turning on

Our ILVE brand rangehood fan has been turning on automatically throughout the day. We've tried to clean it as best as possible, but unsure if this is due to a build up of things or a trippy wire. Looking to get an approximate quote to fix something like this.

The glass on cook Top was cracked. replace it

Hi I need a dryer installed on the wall. Please quote for supply of parts (Suitable Wall bracket, spacers etc.) & Installation. The model of the dryer is Westinghouse 6KG LD605E. It takes the vertical bracket.

Hi there, I'm looking for a professional to hardwire install my Vantrue N4 Pro 3-channel dashcam in my 2019 Subaru XV. I already have the dashcam and the hardwire kit—just need help with the installation. Ideally, you’d be able to come to my place to get it done.

Hi there, Looking for a tasker today between now and 9 or 10pm. Our fridge (side by side freezer and fridge) freezes things/is too cold. Wanting someone to come and check what's wrong - thermistor, etc. The dishwasher fills up but won't drain - there may be a missing part, I'm not sure, or something to do with hose / garbage disposal etc. Several faucets are a bit wobbly, one sink drain is loose/leaking (a silly previous repair done with silicone has failed), a toilet is quite slow to fill/weak flush, and ceiling fans quite loud/one has rusted. Interested for someone to come and diagnose / tell me how to fix, or quote for fixing. I have been trying to figure it all out but would appreciate the assistance and efficiency of someone who knows what they are doing! There is also some failed silicone caulking around I'd appreciate advice on, and I think the bearings are going in our washing machine. Not sure if it is at the point of a broken spider.

We needed to replace an induction cooktop, and the new model doesn't fit into the existing hole in our stainless steel benchtop. We urgently need the existing hole widened by approx 15mm so the installation can go ahead. Images are: - cooktop hole in the benchtop (~90cm wide) - cross section of the benchtop - induction cooktop sitting in the hole showing the issue - close up showing that approx 15mm needs to be cut

New gas cooktop to be installed. Westinghouse model - see photo. Will be installed in the same place as previous one but with an updated bench top and cabinet.