Find experienced local tradies in WA

During rennovation in the laundry area we noticed a sag in the existing ceiling and while tiles were being installed, the ceiling cracked as well as the cornice. Need someone to install a gyprock panel and cornice.

I would like to close down a door permanently that open to the bathroom (single brick wall) . Need bricking and rendering one side.

To render a wall or bag wash in a grey colour Roughly about 25/28 sq meters we are putting caps on top of the pillars Project is in Northam Not sure how much the going rate is for this type of job so please let me know and I’ll adjust my price to suit thank you

Need two low level garden walls rendered

Wanting all walls rendering. Pool equipment we are happy to have not rendered due to not being able to pull this away and we will enclose at some stage. Front of the property we are wanting to use travertine split face 200mm high for the part of the door entrance. Pictures attached of all the walls and a render of what we are wanting the front to look like.

Need walls flushed. All sheets hung already 1 Window and 1 sliding door reveals 6mx6m shed with raked ceilings

I need this built in wardrobe reinstalled into a different bedroom. It is in pieces and labelled clearly. Skirtings need to be cut, wardrobe installed and levelled, wall jams etc to sit flush. I can help with install.

Install a power point in the electrical box outside.

Demolish a wardrobe and remove to supplied skip bin The image shows one of the three wardrobe bays to be demolished. Each bay has a double door and either shelves or having space. There’s image supplied wardrobe spans the entire wall. It is a simple frame and shelf set up and not a flat pack wardrobe. While the condition of the wardrobe doesn’t matter, care should be taken to minimise damage to walls and floors.

We have a finger wall which is needs to be built up to comply with wa pool fence standards. The current wall is 1135mm and we need to raise it to ~1225mm. The finger wall is ~300mm by 195mm. Quite small. We would then need to add a light render to it. So the requirements are to build the wall up about 90mm and render. The job is available to do at anytime from 7am to 7pm. We have plenty of used masonry bricks that can be used but you'll need to cut them to size.

Patch up sand render at house where new plumbing and hot was installed

We would like to render this wall. We had to change the feature because it is close to the pool so can’t have edges more than 1cm deep. Looking to get it rendered or redo a stone on it. Open to suggestions! Area is 180cm tall and 277cm wide.

Im looking for someone to build a floor to ceiling stud frame wall in our master bedroom for WIR. Would also need plasterboard and flushing one side and would like side facing master bed to be sheeted with v-board panels. i also need vertical studs to be 300mm apart. Specs for the room are shown on attached drawing. Cheers

Need our sauna assembled out the back. The boxes are out the front and are quite heavy.

Looking for an experienced plasterer/gyprock ceiling repairer to repair several holes in our ceilings following removal of old lights/exhaust fans and vents. There are 10 areas in total: * 6 small circular holes from removed ceiling fittings * 2 larger holes left by removed exhaust fans * 2 existing ceiling vents to be removed and the openings patched over Photos attached showing the areas requiring repair. The job is to properly patch all openings, reinforce/back where required, plaster/set, sand and finish the ceiling surfaces smooth and flush, ready for painting. We want the repairs to blend into the existing ceiling as neatly as possible. Please supply all materials required for the repairs and clean up afterwards.

Assemble Alpine Cabin sauna. No electrical work required. Job includes disposal of box at end of job. See instruction manual. https://alpinespas.attachments7.freshdesk.com/data/helpdesk/attachments/production/27064343341/original/Cabin%20Sauna%20Installation%20Manual%20250822%20%28web%29.pdf?response-content-type=application%2Fpdf&Expires=1789005528&Signature=DE2d-8N4UatRYHjTzxz4mBBm7DOCYoTwFfkNcACbHHBjBLLtROYrnUgTwPSww6U-a2OzMw3wq3LQnWkFdyzGDF7mJQyTfCom6XjYCOlFSMI88b6-yXDB~zczntRcQ4Dbkb-GVL2JBUDSRv16dtMpZkQSS5HaLErLnwKNnj1MFvLVz~F9ZsPxNDNeiO820oJTgzjRhku3I0Sf1oQdMq2vhz~DJPM4w4~Hi9fHW122M2kCYICseW8kAuTqdQfDKp03z7ItYK2QlSwaW3Hub91xm5jTpsjZUqyrziRQ0U6nsdihnJg1CTq-anmhFXpSRUN~a-cfeO53q8s6nfNS4l-L~Q__&Key-Pair-Id=APKAJ7JARUX3F6RQIXLA

Licensed electrician for Sauna hook up. 9kw harvia (BC90) heater, needs a 40amp installation to three phase power box. Approx 5m straight line distance via roof, access via manhole.

1 x outdoor power point near switchboard 2 x garage power points 1 x outdoor light stopped working for some reason, would like to see if can be repaired

Hi, I need someone to help dismantle anl infrared sauna, safely relocate it to another area of the property, and reassemble it. Would prefer someone with handyman/electrical experience, as I’d also like the power/electrical connection checked or tested to make sure it’s safe before use. The sauna will need to be carefully taken apart and moved without damaging the panels, wiring, glass/doors, or flooring. Task includes: * Dismantling sauna carefully * Moving it to a new location on the property * Reassembling it securely * Checking/testing electrical connection if qualified Please only apply if you’ve done similar work or are confident with saunas, electrical appliances and installations. link for sauna https://rejuvenex.au/products/serenity-full-spectrum-2-person-sauna Flexible with timing. Located in hillarys

Dryer cord got very hot and damaged outlet, needs replaced or at least checked. Dryer also needs tested to see if that was the issue. I work during business hours, can only meet after 5pm or weekends