Find experienced local tradies in Canberra Central

I need a handyman to patch and repair two small areas of damage in my home: Drywall: 1 small hole that needs patching, sanding, and flushing smooth. Internal Door: 1 small hole/dent that needs filling and smoothing. Painting: Both spots need to be painted over to match. I do not have any paint, so you will need to supply a standard white paint that matches or matches closely enough for a neat finish. Requirements: Please bring all necessary tools, patching compounds, sandpaper, and standard white paint. Must leave the areas clean and tidy. Location: Dickson, ACT Budget Estimate: $120 - $180 (depending on paint matching/supply)

Need someone who’s decent at plastering to to plaster these joints and get ceiling paint ready. Area is roughly 2m x 1m

I need a hole in a ceiling plastered and sanded smooth to be level with existing ceiling please. Hole was caused by tile falling but roof since fixed. I'd like tomorrow evening for job if possible or afternoon of Tuesday 22 September before 5 pm please.

Looking for a plasterer to supply and install Gyprock and cornices to a 7.4m x 3.3m steel frame garage. Skillion roof. One end wall has a door/window cutout, the roller door end is completely excluded. Total area is 67m².

can someone patch my wall for a dent??

Repair cracked plasterboard wall, sand and repaint within 2 days

Lower my power point below bench height

A pocket door came off the rails. I tried to fix it myself and made a mess pulling for a bit of drywall up and not resolving the situation so I need the door fixed fixed and reinstalled on the rails properly. I need a large chunk of drywall replaced I may also need some assistance with installing roller blinds and would love some advice on replacing skirting.

Removing several power points from 2 walls in a office.

I power point in lounge room 1 in dining room Double required in 2 hallways 1 double in bathroom

Crack render under window and render blow

I need a licensed electrician to complete the following work: - Replace a damaged double power point in my kitchen with a like-for-like double outlet. - The existing faceplate has broken retaining clips and needs to be replaced. Photos attached. - Install one new double power point on the adjacent wall in the location marked by the red box in the attached photo. Photos of the existing outlet and proposed new location are attached.

I just bought a 2x2.5m Kings awning and need some help installing it into my Jimny

I would like an electrical power point replaced and then a fix to a light fitting that is currently unable to screw in a light bulb

Installed cupboards with multiple blowouts. Need to seamlessly and professionally resection part of the wall

Minor holes in walls need plastering, ready for end of tenancy handover

Looking for 2 practical handypeople to disassemble a 3-person iHealth Premium Infrared Sauna in the backyard of a residential property in Lyneham and stack the dismantled timber panels and components in the garage. The task shouldn't take more than 1-2 hours. This link displays a photo of how the assembled sauna looks: https://foundspace.com.au/product/foundspace-3-person-premium-infrared-sauna/?srsltid=AfmBOop_8OzB8Y8hQ34gTUMBj4WmL-EbEAL0ASxCD1EYojjLE2J-XpNe The job must be completed by or before 12pm Saturday, 27 June. No prior experience with saunas is required, but you must be handy and bring your own tools (cordless drill, screwdrivers, and ideally a soft plastic/rubber mallet). Please note: The largest timber wall panels weigh roughly 30kg to 40kg each, so two people are recommended for the lifting phase to avoid scratching the wood. Key Tasks: - Unplug and safely organise the internal roof wiring (all cables are clearly labelled). - Unscrew and remove the internal accessories, bench seat, and roof panel. - Carefully unclip and lift the interlocking timber wall panels apart. - Stack the dismantled timber panels and components safely and neatly in the garage. Instructions: - I can provide a step-by-step disassembly guide developed using AI to reverse-engineer the process described in this video on how to assemble the sauna: https://youtu.be/rJ7B5swUsU0?si=defqLIzQIpu6QyOp. - It might help to skim through the video to get a visual understanding of the components and how they fit together. Note: Packing, wrapping, and transport are being handled by a separate removalist company who will pick up the sauna after 12pm on Saturday, 27 June. This request is for disassembly and move individual parts to the garage only.

Need a plasterer to patch up two small marks

I need a sparky to do a small job for me, check that this PowerPoint is safe (something fell on it) and put a new face plate on. I can sort out the rest (patching and painting)