Find a professional render repair in NSW

Red brick house approx 65 square. Render whole exterior and paint. Experienced only please. I can provide all materials and paint for after. Just need labour.

There are some areas on the brick at the back of our house where render has been done sloppily or there is spilled paint. I want solutions for how to improve the appearance - see photos

Looking for experienced renderer for one job. All materials need to be supply yourself. Please have a look attached photos.

Patch render block wall. Edges have been damaged and need repair on ceiling. On left had side repair hole caused by digger accidentally hitting it. On right side remove expansion foam and render. I have no materials. Hoping to have it done this weekend.

Need 3 brick walls rendered. Total est 20m2 in total.

I need some areas rendered after removing some cupboards , having some plumbing work roughed in, bricking up 1 window (where the ply is in the first photo), and a few rows of bricks rendered where I am putting in smaller windows then are in there now. Would be probably less than one days work. There are a couple of other areas with small patches. Must have proven experience with rendering .

A small section of cement render needs to be repaired on the front entry of the house.

There’s a wooden board on the wall, once ripped down i need someone to render the brick flat. Not looking for a perfect job. We are getting a mural over it afterwards. Area is roughly in the yellow area. Price is for labour only. Material with receipts reimbursed.

I have three exposed brick pillars and some exposed brick wall that I l just want rendered on my balcony. Photos attached.

Rendering x2 piers Skimming and patching scratches

Repair 2x plasterboard bulkheads and small patch to rendered walls/skimcoat on one side. Approx 4x 400mm verticals, 1x 5m horizontal and 1x 1m horizontal. Setting and sanding required. Painting not required. All material and tools to be supplied by airtasker.

Need 2 walls rendered in a bathroom ready for tile about 8s2 Please note glue has been removed

Remove cement render from internal wall in preparation for damp proofing. Wall is 4.2m wide and render will need removing to ~1.5m

It is a portion of garage wall with 2 small windows

Hang 2 picture frames on double brick rendered walls. Dimensions & Weight: Approx 62cm x 87cm each, plastic front (no glass), and lightweight at max 2.2kg each. Special Note: The hanging hardware/back pieces on one of the frames are slightly uneven (one is higher than the other), so some careful measuring and adjustment will be needed. Hardware: Please bring appropriate masonry fixings/hardware for double brick rendered walls. I will reimburse you for the cost of the hardware separately. If you need any more measurements or info please let me know!

We removed a small section of the brick wall next to the driveway, job is to patch render over the brick on one corner. Doesn’t need to match exactly to existing, just a tidying up job. No painting. Probably suits someone with another job in the area already.

I have had work carried out on my pool and the rendering lifted off, The area is dry and awaiting rendering work. Replacement area is about 3.5m long and 16 - 18 cm in wall height.

Need Gyprocking over 3 Rendered walls. All dimesions in the pictures. need skirting affixed at the bottom as well. check out my other airtasker job listing too

Looking for an experienced renderer to render the exterior walls of a new two-storey building. Exterior walls need rendering Scaffolding is already installed Site is ready for work Please see attached photos for the current condition Please provide your quote including labour and materials Prefer someone experienced with exterior rendering

I’m looking for an experienced renderer to render the existing exterior brick walls shown in the attached photos. Scope of work: * Clean and prepare the existing brick surfaces. * Apply the appropriate bonding/base coat as required. * Apply render over the existing brick walls. * Straighten and level the surfaces where required. * Finish the render using a sponge finish technique, leaving a consistent and professional finish ready for painting. * Protect surrounding windows, doors, pipes, electrical boxes and other existing fixtures. * Clean up the work area after completion. Measurements (Length × Height): * 9600 mm × 2600 mm * 1050 mm × 2050 mm * 3040 mm × 2060 mm * 2500 mm × 2520 mm * 1800 mm × 2490 mm Total wall area is approximately 44 m² before deductions for windows/openings. Please provide your price for labour and materials and let me know your availability. All photos of the areas to be rendered are attached.