Find a local glass fencing contractor near you

Surface Mounted Aluminium Pool Fence Installation: We need approximately 10m of 1500mm high aluminium pool fencing installed along our driveway. The fence is made up of 3 sections of these lengths: 2600mm + 5150 + 1500 No holes or cementing required, you just need to surface mount the flange posts directly onto the driveway. There is a slight slope. You will need to come and measure up and let us know what to buy and we will buy the fencing ourselves. This is the fence we want: https://www.bunnings.com.au/protectoral-2400-x-1500mm-black-aluminium-loop-top-pool-fence-panel-with-mid-rail_p0483469 Photos attached: Aerial photo of the area where the fence is to be installed marked in red. Photos of the area where the fence is to be installed showing the slope and the driveway material it will be installed on (pebblecrete). ** Important: The wire fence in the photos is to remain as is, the new fence needs to be installed next to the wire fence on our side of the border. **

Looking for an experienced pool fencing contractor/fencer to come to Cranebrook NSW and quote on rectifying one section of our existing pool fence. We have recently had a pool compliance inspection and have been advised that this particular section needs to be rectified before we can obtain our Certificate of Compliance. What we need: Inspect the existing fence and our pool non-compliance report. Advise on the simplest and most cost-effective way to make this section compliant. This may involve replacing the section of fence, increasing its height with a suitable extension, or another compliant solution. If replacement is required, we would like it to match the existing fence as closely as possible. The area is near a retaining wall/pool shed, so onsite measuring and potentially some custom fitting will be required. Any proposed solution must meet the relevant NSW pool fencing requirements and be suitable to pass our reinspection. We are not looking to replace the entire pool fence — only rectify the section identified as an issue. Location: Cranebrook NSW 2749 Budget shown we know may not cover everything so inspection is going to give a better idea. Once we know the recommended solution and cost, we can work on and proceed with the work as soon as possible.

Replace 3 panels of rusted aluminium pool fence and rusted corner post. Approx dimensions 2x 3m width + 1x 260cm width, post 120cm high. Fix pool gate latch (not locking). Drive in access next to pool.

Need a few things fixed to make the pool compliant with the QBCC Code.

Following a deck extension we need a glass pool fence moved and additional panels added

I need the current glass pool fence moved and some additional panels added following deck extension

Install perforated pool fence. Materials supplied 16m with gate.

I have been given a non compliant pool fence notice . There are various repairs including - sections around gate where fence is 5mm too short. Possible packers needed under posts. - some retaining structures are too close, possibly replace fence panel with taller panel or use Perspex shield - gate and latch adjustments

Need to install a glass fence on the edge of a concrete patio. I have the glass and the spigots, but if anything else is needed, happy to purchase. 3 glass panels need to be installed, ranging between 120 and 190 cm in length. They are 120cm in height. The base is a concrete slab. Easy access to the installation site.

Please can you quote me to install glass fencing around the pool. 9.57m along the long side and 5.9m across the short side. The are to the right on the short side needs some concrete between the pool and the wooden garden fence.

We have an existing glass pool fence that requires repair. The stainless steel spigots are in good condition, however the anchor fixings have rusted and need to be replaced. Note that each glass panel will need to be removed to access the bracket fixing points (2 person lift that I can assist with).

Need approx 20m pool fencing installed (1.2m high) for the front of the home. 20m fencing will include 1m pedestrian gate and 3m swing open vehicle gate, remaining 16m will be fixed. I can supply materials Please quote

Hoping someone can come with a grinder to help cut pool fence (removed) spigot. Happy for it to be completely removed as well, whatever is easier. Thanks.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.

Need a hand and expertise on taking a glass balustrade off to repair rotted wood below.

UPDATED POST – Please re-offer if you offered on the previous listing as I had to update the details/photos. Need 2 people experienced with frameless glass pool fencing to carefully remove and store 11 glass pool fence panels at a property in Seaforth. The panels are mounted with black base plates/spigots fixed down with hex/Allen key screws (see photos). Job includes: * Removing 11 frameless glass fence panels * Unscrewing and removing base plate spigots/feet * Carefully carrying and storing all panels and hardware on site a few metres away * Handling glass safely without chips or damage * Leaving area clean and tidy afterwards

Looking for someone experienced to help relocate one section of my glass pool fence. Scope of work: • Remove and reposition one glass panel (1800mmx1200mm) • Install one spigot into a garden bed (requires concrete footing, photo 1) • Other side to be installed onto existing concrete post.

I’m putting up a pool fence in peregian Springs . I could use a bit of help lifting and setting the glass panels. Thanks,
Phil