Find a local glass fencing contractor in WA

pool fence re install in a new spot

3m pool fence installed on paving

Install 60m of fence straight line on new existing limestone blocks

I have around 30 meters of pool glass. I’m after someone to measure, mark out and coredrill correct sizing for the material I have

Looking for someone experienced to help relocate one section of my glass pool fence. Scope of work: • Remove and reposition one glass panel (1800mmx1200mm) • Install one spigot into a garden bed (requires concrete footing, photo 1) • Other side to be installed onto existing concrete post.

Glass no longer held in place by rubber gaskets and falling to the ground.

Frameless gate closing mechanism does not fully close the gate and rubs on the ground after about 25% open,

I have some old besko glass pool hinges on our pool fence that need to be replaced. I have bought replacement Polaris 130 hinges and I just need them installed.

Replace 1 steel pool panel and post and then make compliant the junctions with 2 boundary walls.

House has been sold and some of the glass panels in my semi frameless pool fence are not fitting into the posts and one gate therefore not self-closing

Some portion of pool fence has rust , needs repair or replacement . Gate latch is not working

We have just had a pool installed and need a fence erected. We have all the fencing.

The glass pool gate is usually self-closing but now needs to be manually closed. The hinge and latch may need some tinkering. Probably an easy job for those who know what they're doing.

We need the glass installed properly as it’s wonky

Hello, I am looking for a tradie to install a pool fence (see pictures below) in my house outdoor area. The pool fence should be installed between the garage and the grass play area to prevent my kids going into the garage. It's 2 pieces of fence with a gate. The gate will be fixed in between the two pieces of fence and the two pieces of fence will be fixed to the wall. Measurement is 5.4m. I have already bought all the materials needed. Now I just need a tradie to install it for me. I don't know the prices so I've just put $10. So you're free to give me your offer, thank you

Glass gate repair. Need someone to replace the glass panel. Size is about 1.2high by 1.0m (not accurate).

Need a length (approx 7 metres) of pool fence and gate installed to block off side of house.

Would like to have a pool fence installed in this area. Minimum regulation from city of Stirling website is 1.2m high which is what we would like. Brick wall is 900mm so fence would need to step up on to this to complete the required 1.2m height. Total width is 6.1m. Just want something safe and simple, our budget is rather tight as we're doing a lot of reno's currently. I can get a fence kit for roughly $600 however it doesn't include the stepping up on the bricks. I was thinking if it was possible to have a longer panel of fencing and cut to size to include the stepping up and then weld on to the end fence post and fixing to a bracket on the concrete block wall? ** Red scribble Fencing isn't my forte but was playing around with what could work. See my crude drawings OR could we use a rustic panel on the other brick wall to cover that 900mm gap ** yellow/black scribble. Basically someone to come dig the holes for the posts, let me know how much concrete you need for the job, install panels to 1.2m etc. Photos attached. Thanks

Remove existing pool fence and install glass pool fencing. Details: • Remove and dispose of old pool fence • Installation only – glass already purchased • 10mm toughened glass, as-new condition Measurements: • 1 x gate: 890mm (W) x 1160mm (H) • 3 x panels: 1090mm (W) x 1160mm (H) • 3 x panels: 1600mm (W) • 1 x tall panel: 670mm (W) x 1850mm (H) Looking for an experienced installer familiar with glass pool fencing and compliant with Australian pool safety regulations.

Hi I need someone to stick some polycarbonate to the pool fence only in 2 places where the gates are, the material needs cutting and glueing or can use zip. ties