Find trusted local electricians in Sydney Eastern Suburbs

Need a licensed NSW electrician to install a Tesla Gen 3 Wall Connector (EV charger). I will supply the unit (Gen 3, 7.3 m cable, Type 2), so this is labour and materials only. - Single-phase supply - The switchboard is right next to the parking spot, so it’s a short cable run as the charger would go right next to, or under, the switchboard (photo attached). - There are no existing outlets there, so it needs a new dedicated 32 amp circuit Please quote a fixed price that includes the dedicated circuit, any RCD or safety protection required, cable, mounting, testing and commissioning. Please include your electrical licence number. A compliance certificate (CCEW) is required on completion. Timing is flexible over the next couple of weeks.

Electrician needed to find a faulty light in our downstairs circuit. Downstairs lights not working. Upstairs lights working. Wall power points working. Aircon units working. Went out Saturday during heavy rain, so need to locate the issue and resolve. Notes: Outdoor lighting has been tested and no faults. Downstair ceiling lights fusebox breaker not working. Tested with new breaker and still not working. Some downstairs have been checked.

Looking for a licensed electrician to replace 7 existing ceiling light fittings with new LED spotlight bars in a two-bedroom apartment in Tamarama. Scope of work: - Remove 7 existing ceiling light fittings. - Install 7 new Echo adjustable spotlight bars (supplied by me). - 2 × 4-head fittings (kitchen and main bedroom). - 5 × 3-head fittings (living room × 2, hallway × 2, second bedroom × 1). - Connect to existing wiring and switches. - Test all fittings and ensure everything is working correctly. Additional details: - All lights are replacing existing fittings in their current locations. - No new wiring, switches or ceiling cutouts anticipated. - Apartment has standard-height ceilings. - All fittings and bulbs supplied (included images of old and new fixtures) Please quote for labour, including removal of existing fittings and any minor installation materials. Must be a licensed and insured electrician. Flexible with timing. Please include your licence details and availability in your offer.

Looking for a electrician to replace an existing recessed downlight with a hanging pendant light, using the existing wiring where possible. Pendant will be supplied. Photos attached for reference. Located in Waverley, Sydney. Please provide a quote. Thanks!

Looking for a licensed electrician to install an outdoor power point and lockable, weatherproof box for charging my electric bike in Bondi. There’s an air-conditioning unit with an electrical supply further along the same wall, which may provide an easy power connection. Please quote including all materials and labour. Photos attached showing the location and the type of setup I’m after.

Install two x track lights and one pendant light in living area and bedroom.

I’m looking for a licensed electrician to complete a list of small electrical jobs at my home in one visit. The work is straightforward and I’d like it done by someone who can handle all of it together. 1. Split the kitchen light switch so the main light and the spotlights run from separate switches. 2. Install a new dishwasher socket below the kitchen bench. There is an existing socket directly above the bench. 3. Replace a cracked power socket in the living room. The electrician to supply the new socket. 4. Install an outdoor light at the front porch. I will supply the light. 5. Install new socket in bedroom. The electrician to supply the new socket.

Current outdoor lights (connected to mains) are no longer working. I need the current set ip to be removed, troubleshooting to be done(I have bought the lights only) and replaced. I only have the lights so I need wiring and possibly a transformer and a time-based switch. Approximately 50m of wiring required and 20 lights installed.

Hi, I need a licensed electrician for a few jobs at my place in Kingsford (old single-storey brick house). I've already got the main parts, so it should be mainly labour. 1. Living room lights: swap the 6 old halogen downlights for new LED ones (SAL Wave, plug-in type, 72mm cut-out). Remove the old transformers and lamp holders, fit a plug base on a joist next to each light (not buried in insulation), and set the lights to warm white (3000K). The existing holes are about 70mm – please don't enlarge them unless necessary. Test one on the dimmer before fitting the rest, and take a photo of where the plug bases are. 2. Living room switch: replace it with a Clipsal Iconic switch + rotary dimmer (switch on the left, dimmer on the right). Brick wall and the dimmer is about 55mm deep, so it may need chasing deeper. No flicker or buzz when dimmed, and please set the minimum level. 3. Data cable: run one Cat6A cable (about 15m) from the bedroom to the living room through the ceiling, using the existing holes. Cable and keystones are shielded – please bond the foil and drain wire to the keystone at both ends. Registered cabler needed. 4. Safety check: switchboard and roof wiring, especially an old junction point on a timber block. Fix anything unsafe (ask me first if it costs extra). Remove old dead wiring and fittings that definitely aren't needed. Please leave the alarm panel alone. 5. Wiring: let me know if the house wiring is old or worn. 6. Quote only for now – do I need these, and how much? - New switchboard - Upgrade from 80A to 100A - Three-phase – is it available in my street, and roughly what would it cost? - Surge protector I'm also planning ducted AC, a heat pump, solar + battery and maybe an EV charger – does that change anything now? Good to know: - Ceiling and insulation tested – no asbestos. - Ceiling is fragile – please only step on joists. Please include your licence no., ABN and insurance. CCEW needed on completion. Feel free to quote. Thanks!

We would like an old art deco fitting to be removed and a new fan to be installed. Firstly we need guidance on if the fan we selected will work in the existing outlet. Secondly once installed, we would like help cleaning two other ceiling light shades. One in a bathroom and one in living area, mostly as our ladder got stolen and we can’t reach without one. Thanks

Need a licensed electrician to remove cracked broken ceramic cooktop and install new ceramic cooktop 60cm

Replace heat pump on Bosch dishwasher. Error code is E09, so we assume it's the heat pump to be replaced.. Dishwasher is model Serie 4, SuperSilence 46db. Price is for labour. Please advise if you can supply the replacement part and cost of this.

Attach a light fitting to the pendant. Minor electrical work - it just won’t fit over

We have a light that’s gone out in garage and need it replaced. We already have the new light. Just need someone to come do the work.

Hard-wired smoke detector making occasional piercing sound. Unsure what the issue is. Require qualified electrician to inspect and propose remedy.

Looking for a licensed electrician to install 4 customer-supplied pendant lights in an existing terrace house in Paddington. The pendants are opal globe fittings with cord suspension and are to be installed into/with ceiling roses. Existing ceiling lights and wiring are already in place at each location – no new lighting points required. The ceiling roses are already installed. Looking for someone experienced with pendant installations in older homes who can securely mount the fittings through/around the roses without damaging them, set the chain/drop lengths neatly, connect to the existing wiring, and test on completion.

I need to have both kitchen lights next to the exhaust fans repaired, as well as one ceiling light in the kitchen and one ceiling light next to the laundry area.

Replace old outdoor light fitting with a new one. Already provided.

Have two pendant lights to be installed replacing halogen downlights.

Yeah after the plug. No point doing that until done the plug. Could end up damaging the panel when it’s not actually damaged. JOB DESCRIPTION Need an electronic electrician to replace an RJ45 plug. Query broken RJ45 plug and/or an RJ45 socket. Soldering could be needed.