Find a reliable computer and IT professional in VIC

I have an Ethernet cable running from my bedroom to the NBN modem, as depicted in the image. I would like to upgrade to a Cat 6 cable to achieve faster speeds. A 15-meter cable is available.

Title: Configure 2x GL.iNet Beryl AX (GL-MT3000) Travel Routers - Home + Travel Setup Budget: $80–$150 (depending on experience and speed) Description: I need someone experienced with GL.iNet routers to properly configure two GL-MT3000 (Beryl AX) routers: 1 as the Home Router (WireGuard Server or Tailscale Exit Node) 1 as the Travel Router (Client) Goal: When I take the Travel Router overseas, my laptop and phone should appear to be connecting from my home IP address. Current Issues: IP conflicts between the two routers Difficulty logging into the Travel Router WireGuard tunnel not connecting properly (stays yellow) Tailscale Exit Node checkbox greyed out on router I have already done multiple factory resets. I need someone who can: Set clean, stable IP addresses for both routers Configure WireGuard (or Tailscale) properly between them Make sure the Travel Router works reliably when unplugged from home internet Requirements: Experience with GL.iNet routers (especially Beryl AX) Experience with WireGuard and/or Tailscale Payment only after successful setup and confirmation that it works.

Very slow internet on computer as staff have been downloading from Internet sites.

I already changed the battery but is not turning on

I’ve recently completed a new PC build. I’m having an issue during the first time boot sequence: - Motherboard shows orange and red lights, then settles on a white light (with a green light beside it) - CPU and case fans start spinning, then stop. - GPU RGB is on and fans are spinning. - No video output when getting HDMI to GPU or motherboard Specs: nCase m3 grater Strix B850i MB ROG Astral 5080 GPU I need help to diagnose and resolve the issue. This might involve reseating the GPU, updating MB bios, etc. Please note this is a SFF build,

Fiber optic cable needs reconnecting to internet box

My NBN connection box is being installed at the front of the property, and they want to install the internal box where the existing phone connection is. This requires running a cable under the house and they’re not permitted to go under houses. As such I’m looking for someone who is agile enough to access under the house using the access point under the deck and run the cable approx 10m along the existing path and secure it. I have 20 metres of fibre optic cable we can use. I’ve included photos of the access point and where the cable comes out in the house With the right tools and ability I suspect it’d take an hour tops

Not connecting to internet and just general pc setup

This iPad A16 (11th Gen) was in a tough case but was dropped on concrete and now has damage to the screen. There are no cracks in the glass. The touch screen still works and even in the parts that are damaged, it still works when you press something. I would love to hear from experienced people in repairs. I am willing to travel around Geelong to drop it off if necessary.

New keyboard required only I can supply part or you? I can bring laptop to you

My laser printer has a severe paper jam — the paper has shredded and is stuck inside the rollers. I’ve tried removing it by hand but can’t get it out. Need someone to carefully remove all paper fragments and do a test print to confirm it’s working. Should be a quick job for someone with printer/tech experience

I have an old Mac and Apple laptop and a hard drive and I want to put all my photos onto iCloud clean the old computers and dispose of them.

Not sure if it is GPU issue or something else. Monitors not showing up and boot screen not appearing. I need it all up and going urgently for work - so the sooner the better! Tell me whatever you need to assist. I am also looking for IT support with a better backup system too and updates to my PC.

Need a single length of Cat 6a solid copper Ethernet cable run from the lounge room to Bedroom 3. Floor plan is attached. The Run: From the back corner of the lounge room (next to the bathroom wall), up into the ceiling cavity, across to the shared wall of Bedroom 3, and down into the bedroom wall cavity. Access: Excellent access. The roof manhole is located directly inside Bedroom 3, right next to the target drop point. Terminations: Standard single-port female RJ45 wall plates at both ends. No male plugs needed on the main cable run. Materials: Installer to supply solid copper Cat 6a cable (estimated run is roughly 13–15 metres including vertical drops and slack) plus the two standard wall plates/jacks. Looking for a clean, completely concealed cavity install. No external conduit. Single-story residential home with standard plaster walls.

I have conformation from internet company that I’m on line, I have a NBN box and I bought a modem, I’m just struggling to get them connected

Require someone to swap out an ethernet cable under the house. Under the house is quite tight so needs to be a smaller person. It's just a quick job. The area in length would be around no more than 15 meters. Heating ducts can be crawls on top because they are no longer in use.

Need a registered cabler in Melbourne to install 2 Ethernet runs in my house: 1 run for a POE wifi access point. 1 run for a PoE front-door camera. The cables terminate at a point that requires roof-tile access. From there, the camera cables continues through the internal roof space to the front door, and AP location. The AP is also PoE, so both runs just need proper Ethernet termination and testing. Please include: Cable run and termination. Testing. Labelling. Any roof access / tile removal costs. Please quote with and without cable supply.

I need this printer setup to network and laptops

Hi, I’m looking for an experienced ACMA licensed telecommunications / NBN technician to help diagnose an NBN connection issue in my apartment in Melbourne. Background: Apartment building I never previously used NBN in this unit I’m unsure whether the previous tenant ever had an active NBN service I recently started a Telstra NBN service a few weeks ago, but it has never worked since activation Telstra has already completed remote testing and advised: the service is fully activated/open from their end there may be a jumpering / cabling issue there appears to be an open circuit somewhere between the MDF and the apartment line Possible causes may include: incorrect MDF jumpering/patching disconnected apartment line wrong port connection damaged internal cabling open circuit between MDF and unit previous tenant cabling changes building-side telecom wiring issue What I need: proper troubleshooting and line testing continuity/open circuit testing checking MDF patching/jumpering identifying whether the issue is on: the building side MDF side apartment internal line or Telstra/NBN side advice on what repair work is required Important: I have full access to the building’s MDF room Please only respond if you have experience with: apartment NBN faults MDF jumpering telecom line tracing internal copper cabling Ideally looking for someone with proper telecom testing equipment who can accurately diagnose the fault rather than basic ISP-level troubleshooting. Budget currently for diagnosis/troubleshooting only. Further repair work can be discussed if required. Thanks!

Connect robot vaccum to wifi