Find experienced local carpenters in Docklands

Small woodworking job tonight, Docklands. Finish by 10 pm. Looking for an experienced woodworker or handy carpenter to build two small sealed speaker compartments inside an existing puppet-theatre cabinet at Mission to Seafarers, Docklands. Four MDF panels total: measure, cut, join into two L shapes, fit and seal the edges and speaker-wire holes. Tools and materials provided on site. A small job, but needs accurate fitting and someone confident working independently. Allow approximately 1–2 hours. Please reply with your availability tonight.

Looking for an experienced marble or natural stone restoration specialist to remove marks from a kitchen benchtop. During recent plastering works, a plasterboard sheet was left on the marble kitchen benchtop, resulting in visible white/cloudy marks on the surface. Scope of Work: * Inspect the affected marble surface. * Determine whether the marks are plaster residue, staining, or surface etching. * Professionally clean, polish, or restore the affected area as required. * Restore the original appearance and finish of the marble as closely as possible. * Ensure no further damage occurs during treatment. Photos attached for reference. Please only respond if you have experience with marble benchtop restoration and the appropriate equipment. Location: Melbourne CBD / Docklands Please provide your quote and availability.

I have a 74” Scandia Aurora fireplace (electric) that I would like fitted to my apartment. As it cannot be flush mounted into the wall, I would like it boxed out and created into a wall mounted tv unit, plastered finish (I’ll paint it) and 7mm tick oak wall panelling (specrite) installed along the wall. I can supply the panels if required (aprox 8-10) or negotiate a total price inclusive. I am open to suggestions or ideas from professionals for design and price.

Wanting a cabinet maker or carpenter to make and fit a couch base and bunk bed above it on my boat located in Docklands. Timber must be a close match to the current color etc on the boat. Soft furnishings/cushions I will get done after. Just wanting the couch frame with a slide out draw underneath and bunk and a ladder made. Will obviously need to come and measure and discuss design but two photos attached (ChatGPT created) of what I'm wanting with one picture of the current situation. Wanting an approximate cost to do please.

the bed frame long side timber is broken, either replace with that long side/support piece with a stronger piece of timber, or reinformce the broken section by attaching another solid timber length underneath it

Looking for a licensed plumber/tradesperson to remove an existing benchtop and install a wall-mounted stainless-steel sink/trough in a kitchenette/utility area. Job includes: Remove the entire existing left-hand benchtop Install wall-mounted stainless-steel sink/trough Connect to existing water supply and drainage Supply/install required brackets, waste fittings, valves and minor plumbing materials Make good the area after bench removal Keep the existing double sink, taps, benchtop and filtration system on the right-hand side operational No new exposed water pipes should be required, as existing plumbing is already accessible. We will supply the stainless-steel sink/trough. Please provide an approximate quote including labour and required fittings/materials.

I wish to fit a robo vacuum under kitchen sink cabinet. This would require cutting the existing shelves and giving support.

Kitchen Island Timber Slat Modification (Cabinet Maker/Carpenter) Hi, I’m looking for an experienced cabinet maker or carpenter to modify the decorative timber slatted surround on my kitchen island. The current curved front projects too far, preventing chairs from tucking underneath comfortably and reducing legroom. It also makes it more difficult to clean inside the open shelf. I’d like the decorative slatted surround to be modified so the front is flat or has a much gentler curve, while keeping the stone benchtop and existing internal support structure unchanged. If possible, I’d like to reuse the existing timber from any slats or curved rail that are removed so the finished result matches the existing timber as closely as possible.

I have a solid timber buffet cabinet that is approximately 5–10 mm too wide to fit into an alcove in my apartment. The cabinet body fits—the issue is the decorative timber moulding around the base. I’ve already started removing part of the moulding (see photos), but the timber is much harder than expected and I’d rather have someone with the right tools finish it cleanly. I’m looking for someone experienced with woodworking/cabinetry who can: * carefully trim/remove the required section of decorative moulding * keep the visible cabinet looking neat * test-fit the cabinet into the alcove * stop once it slides in cleanly The cabinet does not need to be rebuilt or repaired—only the moulding needs trimming. Please bring your own tools (oscillating multi-tool, planer, router, chisels, etc.—whatever you think is most appropriate). I’d love this completed today or tomorrow if possible. Photos attached.

I will be available all morning tomorrow for an appointment to view the property and work necessary for quote Had to buy a fridge as the old one finally failed. New didn’t fit into the fridge cavity of our built in cabinets. I took out and replaced the floor with a thinner board. Reassembled and complete screwed it up. Need inspection and then estimate to fully repair Estimate given here purely a guess.

Want a Room Divider Wall Panel 100-240cm for an apartment.

Hey there’s. I am looking for a budget friendly custom built cupboard to use for my shoes. In dark colour woody material Sizing in cm: 100W x 115 H x 38D. Will need 3-4 shelves in it and 2x doors on hinges and handle to isolate out weather and dust. Could you please provide a quote? Thank you in advance

I’m looking for someone experienced with carpentry or handyman work to help fix and properly install wooden panels that are already in place. I started this project with friends, aiming to make the panels rotate, but it’s turned out to be more complex than expected. I need someone skilled with measurements, alignment, and making the structure solid and functional. All tools and parts are already available — just need the right person with the expertise to get it done properly.

Bathroom cabinet door has come off and needs urgent repair today. The door is detached from the hinges and needs to be reattached or fixed properly. Looking for someone experienced with cabinet repairs. Please bring your own tools

Kitchen island cabinet panel has come loose and separated at the corner. It needs to be properly reattached, secured, and repaired so it is stable and looks neat again. Please bring your own tools and materials. Located in Doncaster East. Flexible with time.

I need an experienced cleaner or tile restoration specialist to remove stubborn hard water and mineral stains from two of my showers The tiles are matte porcelain stone look tiles. I have already treated the area with CLR which improved it but the staining is still visible especially on the floor and lower wall tiles. This job will require proper professional products and technique suitable for matte tiles as standard bathroom cleaners do not work and can leave patchy marks. Requirements: • Experience with limescale or mineral removal on porcelain tiles • Must bring appropriate products and equipment • No damage to grout or tile finish • Even consistent finish across all tiles Location: Apartment bathroom in Melbourne CBD Goal: Return tiles to an even dark finish without white mineral haze Please include: • What products or method you plan to use • Estimated time required • Similar jobs you have completed Flexible with date and time

I need someone to change these laundry doors that are bifold doors into sliding doors in the laundry area. If a tracking system is installed, it would be on the tiles and not the carpet when aligned. The doors would also need to be made shorter length wise as they may be too tall to be turned into sliding doors. The budget includes the materials to do this task as I don't have any on hand.

Looking for an experienced carpenter to design and build a custom wall-mounted entertainment unit. Details: - Approx. size: 380 cm (W) x 35 cm (H) x 35 cm (D) - Wall-mounted - Finish: Oak and black - Clean, modern look The job includes: - Supplying all materials - Building the unit - Installing it on the wall - All tools, fixings, and labour included - Please quote all-inclusive pricing (materials, build, and installation).

Remove the black decorative panel from the back of the kitchen cabinet

Need two small carpet stains professionally treated (spot cleaning only, not full carpet clean). Diffuser oil stain is small and localised (see photos). Must bring own stain-removal equipment/products. Apartment in Melbourne.