Find a professional wifi technician in NSW

Need help with getting wifi into granny flat , going to buy a mesh router as TPG has stated this will help getting wifi into granny flat and need help with install of 2 foxtel boxes as they do not send out technicians anymore and I have tried myself with no luck

When trying to print from Computer keeps coming up offline. Keep checking printer entering network and password but still cannot seem to get it to work. My husband and I are pensioners and not to Computer savy sorry

I have installed internal and external wifi mesh system eero, however last night and today there is no coverage

Troubleshoot existing Telstra wifi plus wifi extender in main house and setup Ubiquiti Unifi UAP-U6-PRO - WiFi 6 Pro - Access Point in granny flat

I am using Aussie Broadband which offers mesh wifi. I am using a Tenda mesh router which is fixed in the garage. The coverage is not extending to the living room. So I need to fix another box which I already have, to extend the coverage.

I need some computer expert to help assist the wifi range to the floor above with a possible solution to either install mesh or extender as the range is weak from primary router to above floor. Mesh? Extender? Secondary router? Someone who knows this. We have connection with Swoop

I’m in a new place & not good with IT things. I have a new NBN Box (previous tenants didn’t leave it behind) & a new Modem for set up!

I’m looking for an experienced technician to install an IP-COM WiFi access point in the study of my newly built home. We already have IP-COM units installed throughout other areas of the house, however the study appears to have been missed and currently has weak to no signal. I’d like to keep everything within the same IP-COM system for consistency and seamless performance. Important: Preference is for a wired access point (wall or ceiling mounted) rather than a basic plug-in extender, to ensure strong and reliable coverage. Scope of work: • Assess the best location for optimal WiFi coverage in the study • Supply and install a suitable IP-COM wired access point • Connect to existing cabling (if available) or advise on best solution • Configure and integrate with the existing IP-COM network • Test and ensure a strong, stable internet connection Requirements: • Proven experience with IP-COM or similar commercial-grade WiFi systems • Experience installing wired access points (preferred) • Must supply all necessary equipment and tools • Clean, professional installation Additional info: • I’ve attached photos of one of the existing IP-COM units for reference • Also included is a photo of the study ceiling (for mounting reference) • And a photo of the home network/NBN setup and cabling Budget: Open to reasonable offers (approx. $400 depending on equipment supplied)

Connect Netgear Orbi mesh router to exiting home wifi ( 3 pieces)

Setup and configure iiNet ISP on TP Link Archer BE550 modem Setup wireless mesh to TP Link Decco BE65

I need a wifi extender and someone to install

To optimise the wifi connection throughout the house. NBN FTTP connection & NBN box in garage. TPG Ultrafast Unlimited 800/85mbps

Oh sorry I did that in the prior box!

**Diagnose and fix WiFi connectivity on Harvia Xenio sauna controller – Tamarama, Sydney** I have a Harvia Xenio WiFi sauna controller that I cannot get to maintain a stable connection to the Harvia cloud/app. The sauna itself works perfectly via manual control on the panel — this is purely a network connectivity problem and I haven't been able to resolve it myself. **The problem:** The controller connects to my home WiFi and briefly appears in the Harvia iOS app, then drops out again within minutes. The WiFi indicator on the controller panel flashes rather than holding a steady connection. Signal strength near the sauna is strong, so that's not the issue. The pattern of connecting briefly then dropping suggests something is interfering with the controller maintaining a stable connection to Harvia's cloud servers. **Some possible causes I've identified (but haven't been able to confirm or fix):** - DHCP lease instability — the router may be reassigning the controller's IP address, breaking the cloud connection. A static/reserved IP may be the fix - Router settings such as AP isolation or firewall rules blocking the controller's outbound connection to Harvia's servers - The controller losing its cloud pairing registration and needing to be re-paired properly - Something else I haven't thought of — open to your diagnosis **What I need:** - Come to site in Tamarama and properly diagnose the root cause - Implement a fix that results in the controller maintaining a stable, persistent connection to the Harvia app on iOS - The task is only complete when the app is reliably controlling the sauna and the connection has held stable — not just connected briefly You'll need solid experience with home network configuration and IoT device troubleshooting. Familiarity with Harvia or similar smart home systems is a bonus but not essential — the main skill needed is network diagnostics.

Have a working nbn wifi at home. Have a seperate home security modem. Need someone to connect both of them (? Online). The Ethernet cable system in the house is connected to the home security so although the wifi is working, Ethernet outlets are not

I have had Dreame L40’s Ultra Robo vac for about 2mts. It was connected to wifi now is not and can’t reconnect. (All other devices working on wifi) I also need house re mapped as it never mapped it properly to begin with and instructions on how to use app effectively.

Need to set up a 3x mesh wifi system.

1. New NBN installation. Cat 5 from nbn box to router needs to be terminated at each end. 2. TV sound bar install. Set up sound bar and connect to TV

I recently moved into a new house and I can’t get a signal throughout the house . Only if I’m close to the modem . I’m using an old modem I brought with me . Need help to get coverage throughout the house .

Currently I have 3 Unifi AC lite wifi 5 access points across 3 level house. I want them to be replaced with Unifi 6 pro access points which I have purchased. Two access points is a simple removal of the old small bracket and install the newer bracket. No wiring needed. One access point needs to be rewired to move from a room to the corridor. The distance to rewire is about 1 meter. A new hole needs to be drilled in the ceiling and bracket installed.