Find a professional render repair in NSW

1 to 2 weeks work ground floor rendering to new build

Hi, I need a small section of damaged render repair on a low outdoor block wall (see photos) and paint Details: • Damage is approx 50cm long • Located in Cambridge Gardens

I need a very experienced renderer to render part of a front beam Scaffold is there and labourer if needed

Render lower part of wall in a bedroom of a house

Need help rendering using acrylic render (sponge finish) a curved wall to help make the finish more smooth and clean. Please note, the walls have already been painted.

Repair and re-render facade cement render . Flexible on timing Must do a nice and quality job. Have min 4 star ⭐️ rating Must ensure no damage to property and also area cleaned Needs to be arlyric render

Need to repair thin cracks on 2 internal walls and repaint both full walls. • Total crack length approx. 2.5m • Each wall 4m × 2.7m • Cracks are cosmetic only Please include labour and materials. Must repair properly and repaint full walls (2 coats). Photos attached.

Patch up work around the house

Couple of holes left in the rendered wall. They need to be filled and paint touched up. I have the paint.

Need a renderer to skim coat flaked off render. Have three bags of skim coat and render ready to go. Sponge float.

Mount this plaque on cement rendered wall at front of house

Looking for an experienced handyman or renderer to repair minor cosmetic damage to exterior render on a granny flat wall. Damage was caused by an item leaning against the wall. The wall itself is solid — this is surface render cracking/compression only, not structural. Scope of work: • Remove loose/cracked render • Patch and re-render damaged section • Match existing texture as closely as possible • Paint/blend repaired area to match existing colour Details: • Small area (approx. window sill width) • Exterior ground-level access • No structural or brickwork issues • Photos attached

I’m looking for an experienced renderer to texture render an existing front yard boundary wall. Scope of Work: Texture render front yard wall Wall length: approx. 17 metres Wall height: approx. 0.4 metres Even, clean finish suitable for exterior use Match or recommend a suitable texture and colour (optional – please advise) Requirements: Proven experience in texture rendering Own tools and equipment Ability to work neatly and clean up after completion

Need holes for mounting retractable clothes line product Need to be careful of plumbing and electrical behind one wall face Failed to drill using DIY Ozito hammer drill

fix 3 spots where the ceiling cornices are damaged. One has been smashed, this is the photo where it has been taped over in white. The other two are existing cuts were previous built in wardrobes were taken out and replaced with new ones. Render one air vent that has been bricked in. White set tender finish this. Then render in gabs in brickwork in small hallway. It can still look like brick/textured but needs to be flat to make it easier to paint.

Renderer to patch up around existing render

Need to render 2 walls. Doesn’t need to be perfect finish

1*1.2 meter wall plaster work.

Job: Cut approx 1m (or less) Channel in Brick Wall + Install Conduit + Render Back to Smooth Finish Hey everyone Always had a good Airtasker experience Just had my TV hung on the wall I’d love an approx 1 metre vertical chase (channel) cut into an internal wall (brick) to run TV cables (sealed power/AV leads) from the floor up to a wall-mounted TV. Scope of Work: • Cut a neat 1m channel into brick wall (approx. 20–25mm wide, 20–25mm deep). • Supply and install PVC conduit for the wires • Secure conduit with saddles/clips inside channel. • Patch and render back over channel so the wall is flush and ready for paint. Happy to do the painting myself :-) • Finish should match existing wall as close as possible please (smooth render, not a lumpy patch job). I’m happy to handle final painting, I just need it rendered smooth and ready. Job Location : Surry Hills

Need acrylic render fixed and expansion joint to be re cut out and filled with silicone