Find an experienced handyman in Rhodes

Hello. I’m looking for a careful and experienced handyman to help with a few wall-mounting tasks at my place: Hang three mirrors (one small, two medium-sized). Secure one hanging planter to the wall. Move this bed frame to another room. It will likely need to be disassembled and reassembled. The mirrors are delicate and need to be handled with care and precision. Please make sure you have the right tools and wall fixings for secure, neat installation. In about two weeks, I’ll also need help to hang a wall clock, but since it hasn’t arrived yet, that’s not part of this job. And the payment will be made separately. Looking forward to finding someone who takes pride in tidy, detail-oriented work. Thank you very much!

I want to install wall panels on top of my existing tiles in the bathroom area. My wall is around 2.4 m high and 2.6 m wide. I wanted to install. Size of panels: 2400mm x 1000mm x 10mm. Not in the shower area.

Need the old bathroom vanity and shaving cabinet removed and install new ones with new taps. Need the shower head removed and replaced. Toilet bidet spray installed. Shower shelf installed. Toilet roll holder replaced. Need a new kitchen sink and tap installed, you will need to cut some of the bench top (see photos)

Split Level Loft Style Apartment with Gyprock Ceilings LEVEL 1 (A) Ceiling fan install in location with existing batten light (B) Install 2x pendant lights to replace 2x existing batten lights GROUND LEVEL (C) Install 5x down lights in location with 2x existing down lights and 3x existing batten lights (D) Install ceiling fan, new install no existing fixtures in location

3 drawer shoe rack need repair. Side hinges and plastic slider need replacement. Provide quote with and without parts.

I need help removing a wall mounted vented dryer, pictures attached. Item just needs to be uninstalled and placed on the floor, not taken away. Probably a minimum 2 person job. Must be done tomorrow if possible.

Install simple curtains in bedrooms. 4 curtain rods to be installed and gang the curtains

I have a floating shelf that is starting to droop and need another shelf to install new. For the new shelf, it is supported by brackets to install on gyprock.

[Wall mounted Cabinet] Assemble and install a new wall mounted cabinet (from flatpack, rails included) Model : Ikea BESTA 2x120cmx40cmx38cm. [Cabinet on the side] Need to lift the cabinet to have the bottom to be above the skirting board so the back of the cabinet can be pressed against the wall without a gap. So the top will be levelled with the bottom part of the mounted cabinet Need to modify the provided IKEA legs about 2cm to reach above the skirting board I have a 20x8x1200mm hardwood piece for this purpose. The wall material is plasterboard. Please supply the suitable screws, glue and tools to attach the cabinet. [edited: not installing tv mount now and reduced budget]

We have a 1.8m long Ikea unit that needs to get fixed to an existing gyprock and stud wall approx 150mm from the floor. You will need to bring gyprock plugs and screws, we have the Idea Brackets. Its in our office at Rhodes.

Install IKEA bedroom furniture, roller blinds wont roll,fix loosetap, change light bulbs on three lights

Supply good quality retractable flyscreen and install for 2x large windows and a single door. I may add another door to the task depending on feasibility. Windows are 1.8m X 1.8m

I would like 2 toilet seat fittings removed and replaced with 2 I have purchased.

I am happy to drive to your repair shop. I want to fix the paint of my rear bumper. I hit a pole in the parking lot.

I have 6 dining chairs that I’d like fixed. Job as follows: 5 chairs: -tighten dowel joints with a mallet and glue with wood glue to secure - put screws in to fasten seat 1 chair: - see if fixable as the legs have been disconnected

Kitchen cabinet door will not close properly. One of the doors is not lining up, preventing closure. Could be something with the hinges, but not sure.

Blind install for living room and 2 rooms in apartment

My washing machine rubber or door seal needs to be replaced. And make a bit of maintenance of it

We need an experienced handyman or technician to assist with a table assembly issue at a commercial office in the Sydney CBD area. · Securely glue and affix round timber mounting plates to the underside of the table · Drill new holes to correctly align and secure the fluted pillar legs (see photos) · Ensure the table is stable and fully assembled on-sit.e Details: The current drill holes are misaligned and cannot be used. The tabletop and pillar legs are on-site and ready for work. Technician must bring their own tools (drill, screws if needed, etc.) Location: Suite 101, Level 1, Building C, 1 Homebush Bay Drive Rhodes NSW 2138

I would like to replace my undermount kitchen sink with a top-mount one. The current sink size is 69cm × 47cm (irregular shape, the widest point). Details of the new sink are shown in the attached picture. The old sink and part of the countertop will need to be cut out. The drainage pipe will also need to be adjusted, as I’m switching from a double bowl to a single bowl. Plumber License Required.