Find an experienced handyman in Bronte NSW

One side of a sliding door pane has come loose and needs to be tightened up.

Fix hinge on door - internal door - door has come off hinge

I need the back plywood strut of kitchen drawer replaced or fixed and reattached to drawer.

To fix front door and handle and attach vacuum socket to wall

Modify Overhead Cupboards for Ducted Air-Conditioning Unit I’m looking for an experienced carpenter, cabinetmaker or highly skilled handyman to modify the overhead cupboards shown in the attached photos. The two existing cupboard sections marked #3 in red and #2 in blue are currently separate. They need to be converted into one continuous cupboard/enclosure to accommodate a Daikin FDYBA71AV1 ducted indoor air-conditioning unit. Scope of work • Inspect and measure the existing cupboards on site. • Remove the internal partition or other components separating cupboard areas #2 and #3. • Modify and reinforce the existing cabinetry as required to create one long, structurally sound enclosure. Insert a casket inside that is whole size of this new rectangle (#2 & #3 together). • Construct the necessary cabinet casing – the Daiken will be installed in the casket screwed to the top of it. • The new enclosure does not require finished front panels or doors at this stage. The existing doors will be replaced separately. • Maintain a neat external finish in white that matches existing shelfs. Service access in area #3 A service opening of approximately 450 mm × 450 mm is required in the section marked #3. This will also require: • A removable shelf or removable shelf section positioned over the service opening. • The shelf must cover and seal the opening when it is installed. • The shelf must be easy to remove when access is required for air-conditioning inspection, servicing or repairs. • Suitable supports, seals and fixings so the shelf remains secure and does not rattle during normal operation. • Final location and construction method to be confirmed after measuring and discussing access requirements with the air-conditioning installer. Important information • Care must be taken not to interfere with the structural cabinetry, ceiling, cornices, electrical services or other services. • Please advise if any painting or finishing work is included or excluded.

Fix window handle and make secure

Install a privacy lattice on our wooden fence. Need to bring a lattice that would be approx 1.8m x 1m (high)

Install 2/3 support posts and slats for screening. You provide materials pls. 180cm high 260cm wide (Approx)

Hi, I need a reliable handyman or plasterer to fix a some damage to my interior drywall. 3 Locations: 10x10cm, 15x5cm, 2x2cm. I've attached images. We have matching paint. Location: Read St, Bronte, NSW. We have easy parking in our garage onRead Ln. Please let me know your price for the job and how you'd plan on fixing. Thanks!

We have recently had the gym professionally cleaned following a fire in the laundry, where soot travelled up to the ceiling approx - 10sqm. The gym has now been professionally cleaned, however, the walls and ceiling require two coats of paint to restore them properly. We will supply and purchase all of the required paint.

Replace broken mirror with new one, same model and manufacturer. Simple job

Our large aluminium-framed sliding glass door is no longer sliding properly and appears to have dropped/misaligned in the bottom track. I suspect the bottom rollers/wheels may be worn or broken and need replacing, but I’m not certain, so I’m looking for someone experienced with sliding glass doors to inspect and repair it. Please: * Diagnose the cause of the problem * Replace the rollers/wheels or other relevant hardware if required * Check the bottom track for damage and clean/adjust it as needed * Refit and adjust the door so it slides smoothly and closes correctly Photos attached showing the door and bottom track. Budget: approx. $200, including labour and standard replacement parts. Happy to receive quotes if the repair is likely to cost more. Also happy to share videos if it helps. If you can identify what is required from the photos, I would prefer an all-inclusive quote for the complete repair, including parts and labour, rather than an hourly rate.

Recently removed a built in laundry with very tough tiles to remove and we need to fix the render that got taken off the wall before we repaint it. Wall is 1600 x 2200. Plumber is coming to cap off pipes on Friday 3/7, so welcome to come anytime after that.

The screw has come off three draws I need them to be fixed. V quick job.

Hello We need a handyman to come and install baby gates to the top and bottom of a staircase. These are new pressure gates, though drilling or strapping might be required.

Supply and install 2 doors Door 1- 1900mm x 640mm Door 2 - 2050mm x 810mm Including hardware of the door

I have some gym equipment that is mostly assembled, however I lack the tools to properly finish off all the bolt tightening. Quick job for someone with the right tools (multiple wrenches?) and the know how.

Put up ikea beds - malm x2 Help put dryer and washing machine in/plumb washing machine 2x bedside tables 1x coffee table Put up internal locks on cupboards/doors

Please help Tv cabinet has come away from the wheeled attachment Needs to be reattached and secured

I need a confident handyperson to hang a Rachel Donath Dora Gloss Mirror — a premium fibreglass mirror (70cm × 95cm, 17kg) — on an internal pebbledash render wall. The mirror uses a French cleat hanging system (wall cleat + mirror cleat). The wall cleat needs to be fixed securely into the masonry behind the render. 📦 WHAT’S SUPPLIED: • The mirror (already delivered, in box) • French cleat bracket (included with mirror) • Screws (included with mirror) 🛒 PARTS TO PURCHASE (reimbursed on receipt): Before arriving, please pick up from Bunnings Rozelle (Mullens St, Rozelle): • 4 × M8 heavy-duty masonry anchors (Fischer FUR M8 or Ramset Dynabolt M8) • Estimated cost: ~$20–25 (fully reimbursed) 🔧 TOOLS REQUIRED (please bring your own): • Hammer drill with masonry bit • Spirit level • Screwdriver • Measuring tape • Cable/pipe detector ⚠️ WALL NOTES: The wall is pebbledash render over brick. Anchors must drill through the render and at least 50mm into the brick behind. Standard plastic plugs are NOT suitable — this is why we need the upgraded anchors above. ✅ JOB IS COMPLETE WHEN: • Wall cleat is fixed level and securely into the masonry • Mirror is hung and stable • No cracking or damage to the surrounding render 📬 Please include in your offer: • Your experience with masonry/render walls • Whether you have all tools listed above • Your total price (labour + parts reimbursement)