Find a local glass fencing contractor near you

We need to purchase fencing and have someone install it

The pool fence needs new posts as it is rusted and leaning over. It’s mounted on a masonry wall so whatever that will give it more strength. we also need to put some shamfers on the fence so it’s not claimable. i can send the pool inspectors report that outlines what is needed.

Hi, I need a QBCC licensed glazier / pool fencing installer for my frameless glass pool fence job at Ormiston QLD. ✅ What I supply: All glass panels already on-site. The glass is 12mm Grade A toughened safety glass, marked AS/NZS 2208, CSI 7078, PAS-Mark etched on every panel (photos attached). This is second-hand glass purchased privately, original manufacturer contact is unavailable. ✅ Work required: 1. Professional installation of the frameless glass pool fence (approx total length ~10.65m, including gate panel) to comply with AS1926.1 Queensland pool barrier standard. ​ 2. Issue a formal glass compliance statement / glazing certificate (signed, QBCC compliant) confirming this 12mm Grade A toughened AS/NZS2208 glass is suitable for pool balustrade use. This document must be acceptable to my private building certifier for pool approval (Form 16 / building approval). Important note: My private certifier requires this supporting glass document because I do not have the original manufacturer test reports for these second-hand panels. ❌ Not required: I am NOT asking for full Pool Safety Certificate (Pool Safety Inspector certificate) at this stage, just installation + glass compliance statement for building approval. Requirements for you: - Must hold valid QBCC licence for glazing / pool fencing work ​ - Proven experience supplying glass compliance statements for QLD pool certifiers ​ - Can provide references of similar second-hand glass pool fence certification jobs ​ - Can quote labour only (all glass panels provided by me; we can discuss spigots, gate hardware separately) Please send your quote, availability and licence number when responding.

Gate is fixed to house with brackets, one of which is quite close to conduit. Side panel has spigots concreted into a narrow flower bed close to a retic pipe. Ideally the concrete will be dug out and removed with the spigots. If this isn't possible without damaging the retic the spigots can be cut below ground level so the upper parts of them can be removed as long as the parts remaining in the ground are made safe (ie, not sharp). Access is via a side gate (app 1 m wide) on the other side of the house or via a narrow walkway and through the rear garage door.

One glass panel broke and needs to be replaced. 2 aluminium gates are jamming. The first photo of gate A has a gate post that has moved very slightly, just enough to make the gate jam. The top rail of the fence could be cut back where it meets the post I am thinking as it appears to be pushing the post onto the gate. The second photo is gate B and needs easing. I have sketched the glass panels to show the missing panel. Dimensions show panel edge to panel edge not taking into account the space between each glass panel. 4th photo shows where a glass panel has been pushed up from below. It might be OK to leave but should investigate why.

I need approx 10m of temp pool fencing supplied, delivered and installed. Note you need to supply all materials including the fencing, deliver and fully install. The fence needs to go along a limestone edge as pictured. South Perth, 6151, location.

Apply new magna latch to poōl gate certified standards & 2 small brackets

Bunnings mimosa pergola 4 x 3sqm and Bunnings pool fencing circa 5 meters and a gate. All are to be bolted to existing new concrete.

2 glass gates installed into both rock and wood

Looking for someone experienced with pool/spa fencing to install a small aluminium fence and gate onto existing exposed aggregate concrete. Everything is already supplied. The job consists of: * 1 × 970 mm aluminium gate * 1 × 2090 mm aluminium fence panel * 2 × base-plated aluminium posts * SafeTech self-closing hinges and pool latch * Brackets, screws and M10 stainless Dynabolts supplied One panel will need to be cut to size. Posts need to be drilled and Dynabolted into the existing exposed aggregate concrete, then the panel and gate installed, levelled and adjusted. Must have your own SDS/rotary hammer drill and appropriate tools. As this is a spa safety barrier, I’m looking for someone with pool-fence installation experience who can ensure the gate is correctly positioned, self-closing and self-latching.

Re - hang pool fence to be compliant with pool regulations. Fence attached to powder coated posts and fill in drill holes

The pool glass door is not shutting properly. Need to check and fix the issue.

Glass panels are all slowly coming undone and wonkey as ground has moved and posts done align with glass any more. I have had a few panels done with additional spigot support but I want the lot done now: removing the posts and replace with spigots. 10-12 panels need spigots, depending on what’s possible on either end (might need to leave some posts in, especially with the door): I have sourced spigots already. Scope of task: - assess and recommend best way forward with the end and door panels - remove and replace posts with spigots: 10-12 panels - supply tools: to drill holes into tiles without wrecking them - other bits and bobs needed: bolts etc - remove posts from premises: dump run etc Location is Ipswich central. Thanks Oliver Edit: I just realized I did not adjust the budget since I had this task online last time given I have now sourced spigots already and they’re not included in task any more.

We have purchased a house (20yr old) that council has failed for pool compliance. It has a servery window which bi-folds back and once opened stacks approx 40cms from the pool fence. So is deemed as climbable and non compliant. We require a 600h x 800l x 12mm thick clear Perspex and o be attached to the house & top of glass fencing temporarily for compliance. Needs to be done by Friday 5pm

The gate swings slowly and we need to fix it so that it swings back fast and locks

Need to access services under Glass Pool Fence Footing Need x2 Glass Panels removed I don't need the panels disposed. I need to access services that run underneath so will be lifting the papers etc Once we are finished we will reinstall of course new footings may need to be done or spigot placement moved

Pool glass gate isn’t closing by itself. Need fixing to close itself

Fix pool fence gate so that it closes automatically .

We are looking at quotes for the installation of a glass pool fence. Open to negotiation. Happy to purchase all the necessary materials upon advice At this stage just looking at if this can be done and for what cost making sure it meets regulations

This is a placeholder budget. Please reply with your actual quote per metre or a flat rate to inspect and complete the job. I need a qualified handyman or fencing installer to supply and install a pool safety barrier around my Swim Spa steps to ensure it meets WA council compliance. The Setup: Swim Spa steps - Photo for reference Materials Preferred: Black aluminium tubular fencing What needs to be done: Assess the step area to ensure no "climbable zones" are created.Supply and install pool fencing panels Please provide examples of previous pool fencing work you have done. Needing this done asap 🙏🏽