Find experienced local fencing contractors in Malvern VIC

Replace part of a fence that wasn’t done when the rest of it was put up a few years ago.

I need a tradesperson to install a paling fence along the entire side boundary shown in the attached photo. The job involves: - Fixing new pailings across the full 3.3 m side boundary over the existing fence, not just the gap, so the whole section is uniformly clad. - Continuing the paling fence around the corner for 1.4 m to cover and screen the rear shed area. - Include a new plinth board at the base if required to support the new palings and match the existing fence. - Height and style to match the existing fence so the new work blends seamlessly. - Supplying outdoor-grade timber (treated pine or similar) and fixings suitable for external use — no painting or staining required. Access is straightforward via the side path. Please include in your offer: - An estimate of materials and labour for a total length of approximately 4.7 m. - Your availability and estimated completion time.

Looking for someone to build a gate down the side on the house. 1.8m neigh and 1.5m wide.

Need to cut 1 inch off the bottom of our paling gate so that it does not scrape against the ground. Needs to be done neatly without splinters/cracking. Also minor repair to re-screw in gate latch so that it closes cleanly.

Gate continues to slip causing lock and latch to be misaligned.

I need lattice supplied and installed (preferably black) along side fence in backyard and courtyard. Total length is approximately 9m or just under.

$50/hour. Slightly leaning house boundary brick wall. Demolishing brick wall. Tools suppled include eye protection and gloves, crowbar and brick hammer. Stack bricks inside boundary to allow car access. 6 hours labour with breaks for start. You need your own safety boots/shoes. I’ll take of the gate and assist and provide a work platform.

LOOKING FOR QUOTES (work done in a couple of weeks) Supply and install new side gate with walls with top to protect gate and timber walls. Remove old broken timber sides and gate from side of house. Build new timber frame with timber paneling on side of house and on side of fence. Build new gate, gate to be a metal frame with with same style timber paneling on it. Fit new lockable door handle on gate. Lock to be a key lock. All timber to be treated pine and timber paneling will have a primer over it. Get frame secure to house and fence. Dimensions Fence 150cm W, 205cm H. Standard size door (190*85cm)

The fence and gate/door between the house and fence needs to replaced. Looking for quotes for labour and parts

The brick fence that the iron fence is bolted to has moved slightly so that now the gate doesn't close properly and doesn't lock. I've had a look and I think the easiest fix would be to remove the old bolts, place spacers between the iron fence and the brick wall, adjust so that the gate closes properly and can be locked and insert new bolts.

Remove creeper from fence and dispose of it so that the fence can be replaced. Remove clothes line from fence.

Long wooden fence along lane way may need replacement or at least a lot of straightening and reinforcement

Need to attach approx 10meters of wire to top of high fence to meet pool safety regulations. Fence is approx 4 meters high . We have the mouse wire and the staple gun. Dont have ladder or material to chock up under ladder on sloping ground.

Need an exisiting fence removed and a new 40m fence installed. 4 horizontal rails plus a 5th rail for lattice. Post heights range from 2.4 -4.8m. Fence diagram below.

Re place 3 x posts and reattach current fence approx 5m long

Clear. Heavy growth of ivy from back fence

Task is to: 1. remove bush/shrub on paling fence 2. demolish paling fence and remove Location Malvern

Need to replace a dividing fence between 2 properties.

Require a new fence for our property in Malvern. We have a corner block and need an electric gate to allow car access.

Replace timber batten into metal gate frame and paint. Timber batten and paint provided, cutting is not required.