Find trusted local electricians in Plumpton VIC

Im looking for an Electrician to install 2 pendant lights in my living room. Got the down lights already in the ceiling and may need extra switch to operate. Photos attached of the pendant light and where it needed to installed. Need to get done this week. Location fraser rise. Single storey house with access to roof.

Wanting to add power point to marked area, looking to add switch to current switch board pictured. No power source behind wall which is closer so best source would be led light above. Thank you

Missing 240v smoke alarm electrician to replace must provide smoke alarm only free weekends

We need an apprentice electrician to assist with fit out of converted shipping containers will be working with a fully licensed electrician

Electrical recliner chair not working anymore.

Electrical assesment hard wire a 15 amp Rofco bread oven to residential power

TONGLIN Smart RGB Outdoor Lights approximately 90 meters. Require the tasker to have experience in this and prepared to work at height.

Tube light is garage is not working, we bought new tube light still same issue. Seems some issue with either holder or current supply.

Need a qualified electrician to place: - one linear pendant light in kitchen above island bench ( junction box already installed) - Need 3 PowerPoints installed upstairs (Have a Flat roof) will supply the PowerPoint faces for installation. ( Townhouse, no access to roof, as there is no manhole ) - Mount 75 inch TV downstairs need PowerPoint and antenna point changed to inset to fit tv ( I will provide the tv bracket and additional inset for installation ) Will require certificate of compliance upon completion. -

We are seeking quotes to cover the following services: 1. Install x2 new power points in our theatre room. (Closest existing point is behind this wall, at a right angle, on the exterior wall) 2. Install x1 new power point in our laundry room. (There is already one there at a higher point on the wall, the new one would go directly below at the standard position) 3. Replace existing ceiling lights from standard bulb fitting to downlight fittings: x1 toilet room, x1 bathroom, x1 wardrobe Note: The wardrobe light is desired to have a motion sensor capability (if possible, based on advice and estimate). I already have downlights so should not require quotes to include these parts (with the exception of advice on motion based request in the wardrobe). Single Storey House with colorbond roof.

Need lead in conduit installed from nbn pit to house external. 7 metre long from the property entry point.Needs a trench as per nbn compliance.

Need an electrician to swap existing batten lights over kitchen countertop to spotlights. Spotlights already purchased. Also need an existing batten wall light swapped to an actual wall sconce

We have identified some leak in copper pipe in the water heater pump.

Need to change hot water cable

Change kitchen lamp to modern lamp ,I need licensed electrician

Need an electrician to connect dining room light, breakfast counter light, stairs chandelier and ceiling fan in alfresco. All wiring done. Need to replace current Barton lights.

I have 2 downlights in the ceiling that need to be replaced. I haven’t bought new lights because I am not sure which light will work. So, the electrician will need to visit and advise which lights I need. And then install those lights once I buy them in around 30 mins. The hole in the ceiling is 7cm in diameter and the old downlight is 6cm in diameter.

Install 1 Switch Install DETA Grid Connect Smart Inline Switch behind my existing light switch. I already have the inline switch, just need an electrician to install it. Install the Deta Grid Connect Smart Inline Switch (Model 0098816) in-line with the active wire of the appliance or circuit being controlled (e.g. lighting, exhaust fan). This device is hardwired and must be installed by a licensed electrician in accordance with Australian electrical standards. Ensure power is isolated at the switchboard before starting. Connect the active input (L IN) and active output (L OUT) to the corresponding terminals on the switch. Neutral and earth terminals must also be securely connected. Mount the unit in a suitable junction box or ceiling space, ensuring it is protected and not exposed to moisture. Once installed, power can be restored and the device paired with the Grid Connect app via 2.4 GHz Wi-Fi for smart control. https://www.bunnings.com.au/deta-grid-connect-smart-inline-switch_p0098816

8 down lights need new with connection 4 spot light around the house 1 has connected to the electricity 2 chandelier in the living area already has connection 2 pillar light can be solar Please give me quote if I supply you everything else just you need to bring wire

Tv wall install 75 inch . Installing power point . Installing lights over dining table and kitchen island x5