Find trusted local electricians in Leichhardt NSW

I have the aerial and aerial cables but they are now in the wrong place and need to go through outside wall and extended about three metered and bought back through wall into new place

Reverse cycle AC installation for 2-4 units. Ideally requesting a free quote first to discuss placement options

One of my circuit breakers related to my aircon and kitchen appliances has been activated a few times over the last few weeks. I need an electrician to come in and identify the issue. We can then talk about what needs to be done.

Have an old power point ( currently working) but very old. Would like new one installed.

Moving a heavy heat pump dryer (60kg) downstairs to my internal garage

Connect new induction hob Replace light fitting

Require a qualified electrician to install the following into a built-in wardrobe that is currently being put in place: * Cabling and install for 1 light fitting including one switch * Cabling, and install of reed switches and LED lighting on two double wardrobe doors (with 2 LED strips each, so 4 LED strips in total). LEDs to switch themselves on when a door is opened. * Cabling for two separate power points (1 x single, 1 x double) The LED light stops need to fit a certain (standard) profile that I can share. We just need the 'rough-in' of the cabling right now (before Tuesday 16th) and the job can be finished a few days later or also next year, whatever works. Attached drawing shows LED & switch locations. Light fitting is at the top in the middle. Thanks

We are moving house and want to take the lights with us. They were installed by an electrician. Also another small job, tighten up a loose power point.

1 - install of a bathroom 3 in 1 light, replace existing unit with new unit (similar size) 2 - replace pendulum light in bedroom Both easy access with step ladder

I need approximately half a day of electrical work. Can you do this? Happy to discuss what’s possible and rates more. We are replacing the ceilings and have uncovered some very old wiring. It's to; -rewire a few lights (very old circuits) -possible tidy up of some cabling that's all over the place in the roof space -Install two new lights in the ceiling space with a switch -Maybe one power point if accessible to do so The fuse box is relatively new Would be very happy if we could do it tomorrow as I have new ceilings going in tomorrow and Tuesday that make access difficult for a while. Happy to have a chat and explain. Gareth in Lilyfield

New kitchen is being installed. Electricals required. Picture to come.

replace power point and fix ceiling fan/light

Task: Looking for licensed trades to complete a small but specialist job on a two-storey duplex in Lilyfield. Scope: • Supply & install scaffold (suitable for 2-storey front). • Level-2 electrician to disconnect & reconnect street power (point of attachment). • Replace 1 fascia board (H3 treated timber, painted). • Replace 1 sheet of HardieFlex™ cladding on front gable. • Prep & paint gable with Dulux system (undercoat + 2 finish coats, colour TBA). Requirements: • Must be licensed & insured (carpentry/roofing + Level-2 ASP electrical). • Provide compliance certificate for electrical work. • Include all materials, labour, scaffold, and cleanup in quote. OPEN TO ALL OFFERS

Change 10 oyster lights to newer ones and finish the wiring from the ceiling lights to the switches for 1 of them. And also install the wiring for a bathroom wall vent

Looking to reinstall an existing light fixture. Light is already installed but I want the chord to be shortened so it sits higher. See image’s attached. Light is a socket fixture at the base. Job is in Leichhardt.

This is what I need to have done: 1. Isolate the service supply at the point of attachment -single phase 2. Install of single-phase consumer mains from the point of attachment to the main switchboard 3. Install a switchboard meter enclosure 4. Replace the circuit protection with safety switches onto new meter panel x9 5. Install an 18 pole load centre to house circuit protection. 6. Arrange application with metering provider and electrical retailer for metering alterations onto new panel 7. Install current limiting main switch- single phase

Mitsubishi Inverter model SRK35ZMA-S self diagnosis function is indicating that the compressor is overheating. I would like this resolved.

A down light in our bathroom that had been functional for 3 years is now flickering and slow to turn off. Looking for someone to inspect the issue, fix or replace the down light and recommend how to avoid the issue from happening again.

Need to move existing air conditioning ducting (in roof space, so that we can use roof space as storage)

Replacement of led light switches and PowerPoints, materials supplied, approx 15