Find experienced local carpenters in Hawthorn VIC

Hey there. I’m after someone who is able to build and install a cabinet/cupboard above my washing machine (washing machine not in photo). I’m after a cupboard that’s similar colour to the grey next to it, that just has two doors and adjustable shelves (nothing too fancy). It’s a relatively large space above that I would like to have as storage since my washing machine is a washer/dryer combo. Feel free to message for any questions :) Lucy

Shelf unit and cabinet unit I bought from Kmart

I need one small vent hole drilled into the curved stainless-steel dome lid. I will mark the location and confirm the hole diameter before work starts. Looking for someone experienced in drilling stainless steel who has the correct drill bit and equipment to securely hold the lid without denting or scratching it. Please remove any sharp burrs on both sides and clean away all metal shavings. No cosmetic polishing required. Located in Hawthorn. I can bring the lid to a nearby workshop. Please quote for this small job and let me know your earliest availability.

Looking for an experienced handyman or carpenter to carefully remove a temporary timber partition wall in an apartment. The wall is about 3.5 m high by 2.2 m wide and was built to divide the lounge and dining area. It is a timber-framed structure with insulation batts inside. It sits alongside an existing brick wall, which must not be damaged. What I need: Take the wall down carefully and methodically Protect the adjoining brick wall, floors and nearby surfaces This is an apartment, so noise restrictions apply. Work will need to be done during permitted hours and as quietly as reasonably possible. Please confirm: Your availability and a fixed price Please only quote if you have done similar internal demolition or partition removal before. Cheers,

Please help to set up my workshop space, by securing my benchtop and vice. Also set up my Dad's wood lathe, to re spark my turning hobby.

Custom Eyewear Display Cabinet Looking for an experienced cabinet maker/shopfitter to build and install a custom eyewear display in our optical store in Hawthorn. Approx 2400mm wide, consisting of: * Two equal display sections with a central mirror * Approx. 6–7 shelves each side * Integrated LED lighting * Timber finish to match existing cabinetry * Slim side panels * Existing lower bench/cabinetry and green fascia to remain

Need a front decking stained 1.5 x 14m estimate

Stained glass window to be fixed on-site. See attached images.

I have two of these hinged cabinet doors that I need taken off as soon as possible

Build & Install Custom Oak-Look Storage Cabinet in Decorative Fireplace (Nursery) Looking for an experienced carpenter, cabinet maker or skilled handyperson to build and install a custom storage cabinet within an existing decorative fireplace in a nursery. The goal is to create a clean, built-in appearance while preserving the original character of the fireplace, including the exposed brickwork and hearth tiles. Fireplace dimensions * Opening width: 865mm * Opening height: 845mm * Depth: 367mm * Existing brick lip at base: approximately 90mm high Proposed cabinet * Approximately 700mm wide * Approximately 400–450mm high * Approximately 320–350mm deep * Two push-to-open doors preferred (or drawers if you believe this is a better solution) * Oak-look finish (veneer, laminate, plywood or similar) * Cabinet to sit recessed within the opening, leaving exposed brick visible on both sides and above * Existing brickwork and hearth tiles to remain visible and undamaged Scope * Site measure (if required) * Build cabinet * Construct platform over existing brick lip if required * Install cabinet securely * Achieve a neat built-in appearance with quality finishing Style Looking for a warm Japandi / Scandinavian aesthetic that suits a period Melbourne home. Please include: * Photos of similar cabinetry or built-in projects * Whether materials are included * Estimated timeframe * Approximate cost Located in Hawthorn VIC. Happy to receive suggestions if you believe there is a better way to achieve the same outcome while preserving the fireplace character. One of the attached pictures is a rough concept, the other is the existing fireplace.

Hi, we have recently had new carpets installed. The new carpet is slightly higher than our old carpet and now the doors are getting stuck. We need the doors in two bedrooms slightly cut/shaved so they move freely over the carpet. This needs to be done on Friday , 8 May.

Hi, I need a red gum. Post base turned to the top to match the original profile. I need two of them. I have the red gum block. I just need it turned at the top. It’s about 4 inches of turning. It needs to be done on a Timber lathe. The original is 170 years old and needs replacing. The largest dimension of the block is 150 x 150 mm

18 month old external stairs. Timber balustrade and timber handrail require sanding and re-staining. Main set of stairs going up 1 storey (see photos) plus a second small 3 step stairs outside laundry. The main set of stairs face the sun and timber sustained a lot more wear and tear. The steps are made of steel, so the job is only for the balustrade and handrail. Please see photos.

Looking for an experienced cabinet installer for a residential project. Scope includes installation of pre-made cabinets, alignment, leveling, and secure fixing. Attention to detail is very important – clean and precise finish required. Must have prior experience in cabinet/joinery installation, own tools, and be reliable. Location: Hawthorn Timing: weekend Please send your quote (hourly or per job), availability, and photos of previous work. I am comparing multiple quotes, so please provide your best price upfront. Potential for ongoing work for the right person. Only experienced installers please – not suitable for beginners.

Bedroom cupboard doors have come off. The wood has split/ cracked. Need someone who can either replace the panel or fix it some other way. Simply drilling the screws back into the wood won’t fix it, we have done that and it eventually just comes off again. I can imagine it’s a fairly easy fix for someone who knows what they’re doing. We have 3 x cupboard doors that need fixing

Manufacture and install a custom book hutch / bookcase in a nook beside a door in an apartment - the design would be white, following the inspiration of the top of the curve in this example image but not the bottom curve. The cabinet would need a back for strength for the books and the shelves would be 25mm adjustable (or other measurements, on advice). The back inside would need to be paintable so it can be painted in a feature colour. The dimensions of the space it’s being installed into are roughly 420mm deep, 2127 mm high

Custom bathroom cabinets

Looking for an experienced concreter to grind, stain, and seal approximately 35sqm of existing concrete flooring in one room. Scope of work: - Grind existing concrete surface. - Apply concrete stain (colour to be discussed). - Seal with a basic satin finish. If possible, install a transition strip to neatly separate the concrete area from the adjoining carpeted section. Additional details: Indoor job. Access is straightforward. Must supply own tools and materials (unless otherwise discussed). Previous experience with decorative concrete preferred — photos of past work welcome. Timing: Ideally completed by 26th February, but happy to negotiate the date for the right person :) Attached are photos of the room - the carpet will be removed and room cleared out before the job begins to ensure there is enough space to work :) Please include your experience, availability, and a rough quote when applying. Thanks so much!

Attend on-site to provide written quote for supply and installation of wooden beading at edge of skirting boards and wooden floors on ground floor of old house. One room has already been done; 3 other rooms need to be done. The beading will need to match the flooring in the 3 rooms, so need to visit site for visual inspection before providing quote. Supply and installation of the beading are not part of the scope; those will come later.

I need you to cut a 2400m block of vic ash hardwood in half in my garage. So I then have 2 pieces that are 1200 each. Width is 600m, depth is 33mm. I don’t have any equipment but I have a space in garage or back yard where you can do it. I want the cut to be clean and neat as it’s being used for a desktop. Thanks