Find an experienced gas fitter near you

Red flame, unstable, only one of 5 is working. I need someone to fix my Bosch gas cooktop, 5 burners please. Serie 8.

Remove replace my gas counter top cooker

Need to check gas leakage and fix Need to fix dishwasher mixture head pipe

Got two small jobs, ideally same visit: Connect a gas BBQ to an existing gas point – I've already got the conversion kit. Install a mixer tap (tap supplied) onto existing hot/cold points. All the gas, hot, cold and drainage points are already in place - photos attached. Just needs connecting/fitting. Please respond by email with: 1. Your quote 2. When this can be done or any questions you may have

Need to disconnect a gas line from a cooker, there is no isolation valve so it will need to be capped. Range hood to be disconnected from power, im happy to remove it if needed but just need it disconnected.

Experienced handyman (better 2 workers) needed to overhaul an L-shaped polycarbonate multiwall patio roof. All premium replacement materials are provided by me (Laserlite H-bar/U-shaped gaskets, breather/sealing tapes). You provide tools and labor. Site Details & Heights: Roof Height: ~2.7m from patio / ~2.2m from raised garden bed. Ladders on-site: 1.7m A-frame and 4m multi-position ladder available. 10 Panels Total (11 vertical H-bars): * 1 panel: 0.84m x 1.85m (Far left, needs bad DIY redone) * 3 panels: 1m x 1.85m * 5 panels: 1m x 3m (Deep section) * 1 panel: L-shape transition junction **Scope of Work:** 1. **Disassembly:** Remove 11 aluminium H-bar caps and old gaskets. Shift panels as needed. **Crucial:** You MUST bring your own structural plywood/crawling boards to bridge the 1m timber beam gaps and walk across the 3m spans. Do not step on plastic. 2. **Clean & Dry:** Pressure wash dirt/algae from internal panel channels using a mild bleach solution. **Mandatory:** Use a leaf blower/heat gun to dry inside the hollow channels 100% bone-dry before sealing. 3. **Trim & Tape:** Top edges get white Sealing Tape. The current bottom aluminum trim is a single long bar causing buckling. You MUST bring an angle grinder/hacksaw to cut it into 10 separate short sections matching each panel's net width (leave 3-5mm expansion gaps). Apply mesh Breather Tape, fit rubber U-gaskets, and press cut trims over them. 4. **Reassembly:** Thread new gaskets full-length into the 11 vertical caps so they compress tightly against the bottom end-caps. Slide panels under house flashing and screw down tightly. **Tools You MUST Bring:** * Plywood / crawling boards (essential for 1m spans) * Aluminum cutting tool (Angle grinder/hacksaw) * Pressure washer & Leaf blower/heat gun * Cordless drill with 5/16" hex socket https://www.justritestore.com.au/assets/Brochures/2024.0689-Multiwall-Brochure-Update-2024web6485.pdf see this diagram

I need a certified plumber to disconnect and cap the gas line below the cook top due to kitchen renovation due that the customer will have an electrical cooktop instead. Just disconnect, cap the copper line at the wall. Must provide certificate Probably less than half hr job. Give me an offer and happy to sort out through here or onsite.

licensed gas fitter: 1. Confirm the outlet is still connected to natural gas. 2. Pressure-test the bayonet valve for leaks. 3. Replace the bayonet socket if it’s worn. Advise best heater for house and install

Licensed plumber required Decommission/remove gas outlet, close off and put beneath floor. Close off pipe which has been accidentally cut and runs from the mains (pipe is black plastic) Located in Balgowlah.

Old house, the feed in pipe from the gas mains goes in through a window which I'm getting repaired so want it to trace along an inside wall, I'll even pre drill the route. To me it looks simple but I'm not confident about gas work, Check out the photos and hit me with a quote.

Need Licensed Plumber – Decommission Gas Line. Looking for a licensed plumber to safely turn off and cap an existing residential gas line. The gas supply is no longer required as the appliance has been removed. Need the job completed ASAP. Please bring any fittings required and provide a gas compliance certificate if applicable. Flexible with timing and happy to meet on site at short notice.

Need kitchen sink, gas cooktop and tap disconnected for kitchen demolition and complete removal. Need them all completely removed to within wall cavity. Please note that gas has been fully disconnected from the property, so there is actually no gas running to the cooktop. It just needs to be removed to any point within the wall.

Install a gas bayonet taking gas from inside kitchen cabinet wall to outside of same wall facing lounge room. It's a straightforward job, minimal distance to run. It's for an unflued gas heater. Easy access.

Plumber needed to disconnect gas cooktop, seal gas supply.

I need to disconnect combi oven, char griller, and deep fryer from my shop at haymarket and move it to other place on CBD

Hi there, I need a licensed NSW gas fitter to rectify a gas installation defect identified by Jemena on my property in Eastwood. The defect noted on the certificate is: "Earth stake & weep holes in exclusion zone". Scope of work: Relocate/extend the gas regulator vent line or pipework to ensure it is clear of the electrical earth stake and building weep holes (per AS/NZS 5601.1 standards). Perform a pressure/leak test upon completion. Issue a formal Certificate of Compliance and a Leak Test Certificate as required by Jemena. Please refer to the attached photo of the Jemena Non-Compliance notice for exact details. Must be fully licensed and insured in NSW. Please provide your license number when offering. Flexible with timing but needs to be completed within the next few days. Thanks!

Require a gassfitter or plumber with gasfitting endorsement to safely disconnect oven gas line etc in order for kitchen to be removed and line made available for next kitchen install.

I’m looking for a licensed gas fitter to inspect and repair an LPG gas leak at my home. The leak appears to occur where the pigtail/hose connects to the LPG gas bottle. I need the issue diagnosed and repaired safely. The task includes: * Inspect the LPG bottle connection and pigtail. * Diagnose the source of the leak. * Repair the leak if possible. * Replace the pigtail, fittings, seals, or regulator if required (parts can be quoted separately if needed). * Test the system after the repair to ensure there are no leaks and it is safe to use. I’ve attached photos of: * The LPG bottle valve. * The pigtail/hose connection. * The regulator and gas line. * The overall gas installation. Please only respond if you are a licensed gas fitter and can provide the appropriate compliance paperwork if required.