Hire a professional washing machine services in Central London

The washing machine door latch needs to be replaced. Washing machine model: IWDE126. The door latch is faulty, and currently the machine door does not close properly.

my washing machine keeps flashing everytime i press start and i’ve checked child lock and the doors and it still won’t wash

Washing machine needs fixing - won't spin, likely as water not draining properly. Done some initial investigation but now need a professional. Machine will need pulling out of its position which will be difficult. Machine: Indesit IWDD washer-dryer (7kg + 5kg) Symptoms • Won’t spin. Spin-only cycle: timer counts down but motor never engages - no sound, no attempt to turn. • Drum rotates freely by hand. • Door lock engages correctly (single click on cycle start). • No error codes displayed. Diagnostics performed so far 1. Pump filter cleared. Removed kickplate, drained via filter, found a significant plastic blockage inside. Removed it. Impeller inspected — looks intact, spins with magnetic detents (normal). 2. Spin re-tested after filter clean - still won’t spin. Empty drum, so not an imbalance issue. 3. Drain/rinse cycles confirmed pump runs - humming/whirring audible for ~30 seconds. 4. Tilt test revealed water still sloshing in drum despite pump running and filter being clear. 5. Rinse + spin cycle attempted - significant water came out via filter afterwards, confirming pump is not fully clearing the drum. Best Guess So Far Pump runs but flow is restricted. Spin is then inhibited by the pressure sensor detecting residual water (safety interlock), which explains why the motor never engages. Possible causes: 1. Blockage in the sump hose (corrugated rubber hose between drum and pump) - possibly secondary debris from the original plastic blockage. 2. Damaged impeller blades not visible from filter side. 3. Weak/failing drain pump. Not yet checked • Sump hose (would require tilting machine). • Pressure sensor / pressure chamber hose. • Motor carbon brushes

The washing machine doesn’t seem to be able to spin anymore or complete any wash program. The model is Indesit IWDE126

I need two washing machines uninstalled at two different properties 20 minutes apart and then one of the uninstalled washing machines are coming to the other property to be installed. This will need organising by the Air tasker

I have a few items which need to be done would prefer a cost once all items are reviewed. Thanks

Spin and drain humming water not draining

Hi I have a s a Haier washing machine model (CAS: 31011222) F4 error on a Haier washing machine typically indicates a heating element fault — the machine isn’t reaching the expected water temperature, which points to either: • A faulty heating element • A faulty NTC temperature sensor • A wiring issue between the two

Looking for a plumber to install a proper cold water feed valve for a washing machine. There is an existing cold water pipe in place, but it does not currently have a standard threaded outlet suitable for a washing machine hose. The job is to fit a suitable isolation valve with a 3/4" threaded connection. The waste pipe is already in place. Access is straightforward (see photo).

Washing machine belt recently replaced but moving out of position and causing a rubber smell, need someone to diagnose and fix.

Washing machine drain requires unblocking by specialist (currently causing leak into downstairs flat ). Flat is in London bridge

Received a new washing machine in my new flat need help to install it.

I need a section of the skirting board in the kitchen cut out to be able to remove the washing machine which is currently integrated so we can install a freestanding one. need the sides where it has been cut left neatly and not rough.

Washing machine leaking, unsure why

Washing machine SMEG WDI14 C7

Hi, I need someone to help with a drainage problem. My washing machine isn’t draining properly and when it does drain, the dirty water backs up into the kitchen sink. There’s also stagnant water left sitting in the washing machine drum and it smells bad. I think the shared waste pipe between the sink and washing machine is blocked or draining very slowly. I need someone to inspect it, clear the blockage, and make sure the washing machine drains properly again. Ideally looking for someone affordable as it should be a quick job.

Current connector to washing machine has a slow leak (as evidenced by the limescale on pipe on the picture). The valve needs replacement, the pipe needs clearing of limescale, and the dishwasher needs reconnecting.

Experienced Plumber Needed My washing machine currently pumps water into my kitchen sink drain, causing water to back up into the sink when running a wash cycle. Both appliances share the same waste pipe and this issue persists even after basic cleaning and checking for blockages. I am looking for an experienced plumber who can: -Diagnose the plumbing configuration under the sink and washing machine.Identify and fix any underlying blockages, incorrect connections, or pipe sizing problems. -Reconfigure connections and pipework if needed, so that water from the washing machine never backs up into the sink. -Advise on and implement any long-term solutions to prevent this issue from recurring. Please respond with: -Your plumbing experience with similar drain/waste pipe problems. -An estimate for inspection, diagnosis, and full repair.Approximate timeline for completion. -Task must include all parts, labour, and a warranty for the fix. Job Location: London, SW129AZ

I need my washing machine removed, and the new one installed

E10 error code. I’ve got this working again so many times checking for kinks, water pressure and the inlet but eventually the same code appears each time we try to dry the clothes and also when washing. Machine is a Zanussi Lindo 1000