Find local Mira shower repair experts in Central London

Looking for handyperson/plumber to replace a deck-mounted bath shower mixer tap and fit/ a new bath panel (183cm x 50cm). Located in SE14

fit new shower head (replace rain shower head with filter shower head)

Shower rain head not working (rest of shower working) - assume will require unscrewing hose and putting back together. See attached.

Install new electric shower

Porcelanosa/Noken panel with three knobs, see photos. Knobs have become very tight, difficult to turn. Knobs not held in with screws. I think model number is 100140559, The diverter handle has become very stiff and the bath flow control is also quite stiff, although both still work. I suspect the diverter and flow cartridges need servicing or replacement. I have bought new cartridges should they need to be replaced.

Hi, I have a shower tray that was installed directly on the floor, and I suspect it wasn't done correctly. I am experiencing bad smells coming from the drain and I am worried about water leaks underneath. I need someone to inspect the plumbing connection to check if the waste trap is working correctly or if there is a double-trap issue. I also need to verify if the tray was properly sealed with flexible adhesive and if a waterproofing membrane was used underneath. You might need to lift the tray to fix the seals and the drainage. I didn’t know what to put in the price so is obviously negotiable

Connect gas cooker, instal glass shower screen and fix wardrope doors

Move the exiting shower head in to the ceiling with a flush-mounted ceiling shower head (example picture attached) Requires 1. Removing the tile it currently comes out of 2. Remove / or move the light 3. Replace tile 4. Make right ceiling The show tray has a gap whit the wall as the wall is concave. And it has been filled with a large amount of silicon. I want a proper fix to this for example retro-fitting a sealant strip before siliconing Please only respond if you are a plumber. I do not want any handyman services

Water goes out of the shower head I guess it needs tightening

The shower is not heating properly as it used to be. Apparently it has to do with descaling and checking the filter.

The Tap Factory Vibrance Vanto concealed thermostatic shower. Temperature control is now free-spinning continuously and the shower is stuck on very hot. The temperature control has never worked properly since installation. Two days ago, after many rotations, I managed to get the shower to output cold water, including briefly with the hot supply isolated, but it has since returned to hot and spinning the control now has no effect. Suspect failed/stripped temperature control mechanism or thermostatic cartridge. Looking for diagnosis, repair and recalibration. The original installer mentioned possible hot/cold pressure imbalance, but all the other mixer taps in the flat regulate temperature normally. Maybe we need to check the dynamic hot/cold supply at the shower itself as well as the failed temperature control

Sensor that triggers hot water has gone water only in the shower keeps going cold

We have a mira sport max electric shower (9KW) which appears to have suffered an electrical fault. We’ve had a plumber out to review, who has confirmed there are no plumbing issues, so we would really appreciate some help diagnosing and fixing the problem.

Leak from shower console, were the handle inserts. Can provide clear videos of problem, new console on order but would prefer a professional to fit it.

Hi! I need an experienced plumber or handyman to replace the concealed thermostatic valve element in my shower (Scudo brand). Part: The replacement thermostatic element is already purchased and on-site. Access: The existing shower system is a concealed valve setup. Photos: Provided Requirements: - Please bring your own tools and white silicone sealant will be required. - You must have experience working with concealed thermostatic shower valves. - Please ensure the water is turned off safely, the element is swapped cleanly, and the seal is tested for leaks and temperature control before finishing. Thank you.

I need a new shower pump installed in my bathroom - part (pictured) has already been purchased, as I have needed to replace it before. Pump is located in a partition behind the sink and easily accessible

Shower valve thermostatic cartridge has failed. Unfortunately the retailer can’t source a replacement cartridge so I’ve had to buy the whole shower valve again and it needs to be replaced like for like.

I need to replace my current shower head with a new filtered shower head. Based on an engineer looking at the current shower head, light plumbing work is needed to remove the current shower head so it is possible to install the new one.

We need a shower replaced. The new one is due today (Tuesday 2nd) and the old one will need to be replaced with the new one. The new one is a Cruze Modern Thermostatic shower. We’ve checked measurements and all looks fine, but let us know if there’s anything else to check ahead of arrival. Would like ASAP please.

need help replacing my old single bathtub taps with my new mixer one that comes with a shower. and also my old sink taps needs to be replaced with new 2lever taps. (the new fittings are black seen in picture) - please, somebody local because i wont be paying for your travel/congestion