Find a professional local carpenter near you

Recently did a deep clean of our oven using a solution kit, the bag was left on our kitchen counter and the residue has stained our worktop. Need to get this restored or the stains removed. Price flexible

The MDF bar that sits above the built in dishwasher has warped due to moisture and heat exposure. We need someone to remove this, and replace with a new piece of moisture resistant, painted wood. The wood should be sealed into place with a sealant. The selected airtasker will need to bring all materials and tools required to do the job.

Timber framing for a suspended ceiling room is 3x2 Install a dishwasher

remove old and Install new Kitchen sink waste Stainer

Build a cabinet door and install

Kitchen cabinet cut to fit space- looking for carpenter/ joiner - max 1 hour job The pre assembled kitchen cabinet doesn’t fit into the space I need it to due to an extra ledge on the lower wall ( will upload photos) therefore the bottom of the cabinet needs to be cut around this area to fit into the space and the cabinet door needs to be screwed on at the end

Joiner to fit an IKEA PAX wardrobe for a seamless built-in look. Tasks: assemble, level on 60–100mm plinth, fix to wall, tie units, add MDF side scribes and top infill (continue coving if needed), notch/refit skirting, hang/adjust doors, make good (fill/caulk/sand/prime), remove packaging/waste.

I need someone to build my bathroom cabinet

I need help raising the cabinet 15cm and make it look like it’s fit to the wall on the sides . Job includes building platform and adding side panels on sides to fit to wall plus screw cabinets to wall Two cabinets in total

I need 2 x internal wooden doors trimming. The heights are currently too tall due to some carpet being fitted a few years ago. Ideally this will include taking the door off and putting back on. Note, they are old doors and are pretty solid/heavy ish.

IKEA EKET cabinets for 3 to install in my reading room

I would like to have two rectangular openings cut into the back panel of my hi-fi cabinet (photos attached) to allow easier access to cords: • Bottom shelf opening: approx. 410mm wide × 150mm high • Middle shelf opening: approx. 410mm wide × 100mm high The cut edges should be sanded smooth. The cabinet is made of mango wood, and the back panel is about 12mm thick. Please let me know if you can carry out the work on-site at my home in Enfield, or if the cabinet would need to be taken away. I am flexible on timing and happy to work around your availability. Quotes including labour and any necessary materials would be appreciated.

I am in the process of refurbishing a house, and need to replace part of a vertical skirting board.

I have a wood pole that needs to be propped up from underneath. Or a piece of wood on the top. I’m looking for a quick temporary solution. Needs to be done by tomorrow 5pm Thanks

Need support in fitting fittingly furniture. Might need to cut certain pieces as some is slightly longer Essentially a cabinet with some shelves and one drawer to fit into this nook

Looking for a joiner to install banquette seating in kitchen corner, and remove existing breakfast bar. Also to install shelving in living room alcoves. Small residential project but may be more scope for future projects as I am an interior designer. Please see my profile for further details. Please quote below or contact me. Thank you!

Apply good carpentry and furniture manufacturing knowledge to: - take 4 solid oak legs (see photo) - router the top out according to specs at R100mm radius (see specs) - Apply R50mm edge blend to 90 degree edge Designer and business owner with more jobs on the way - looking for a long term partnership with many more high end projects with anyone who has high attention to detail, care and skill for high end furniture prototypes!

Hi, I am looking for someone who can sand and polish a small patch on my wooden table.

We’re looking for a carpenter or maker to help build three chairs based on some attached plans. This is a fun, light-hearted project — the chairs are for casual use around the house or garden, and we’re not being precious about the outcome. We’re imagining a simple build using pine or plywood. They don’t need any fancy finishing — just sanded enough not to be rough to the touch. Raw, honest construction is part of the charm. What we’re looking for: – Source and supply the wood (ply or pine) – Build 3 chairs from the plans – Sand to remove roughness (no paint or finish needed) – Ideally deliver to Tunbridge Wells (or we can arrange collection) We’re open to suggestions or tweaks if they help make the build easier.

Demolish and completely remove from the property a wooden shed. I can then help clean the concrete base and surrounding area before you construct my new shed. It’s a Keter Darwin resin 6x4 tongue and groove easy fast assembly shed with a floor panel. H:205 x W:119 x D:184.5. Combined weight of the panels = 61 kg. I’d also like some old items from the shed taken away such as a couple of hoses, a large garden parasol, etc. Those are the big items, the others don’t weigh much.