Find an experienced handyman in Outer West Sydney

Replace fly screen with pet mesh and add a screen door doggy door. Already have pet mesh.

Repair damage to garage doors. The images shown are of both sides of the same wall. I will paint the walls.

Replace 2 x coolroom sliding door wheels.

I'm looking for someone to supply and install 13mm gyprock soundcheck on a single 2.7x3.56 wall. Quote is to remove existing plasterboard, supply and install new plasterboard including cornice. Use of acoustic clips to mount to frame and acoustic sealant around perimeter. Preference given to someone who has experience installing plaster with acoustics in mind - Price negotiable. More work available. Client will supply wall insulation for when frame is exposed. Trade to supply all other materials. Client will finish architraves. Client will dispose of old plasterboard.

Install a freestanding letterbox into the ground at my property. The letterbox comes as a solid unit that needs to be securely fixed into the ground. Scope of work: -remove existing mail box (partially soil and cement) -Dig hole suitable for secure installation -Supply and pour concrete footing -Install and level the letterbox correctly -Ensure it is stable, aligned, and secure Requirements: -You must supply all tools and materials (concrete, etc.) -Ensure a clean finish and remove any excess material/rubbish Notes: -The letterbox has already been delivered (large boxed item) -Easy access to installation area (please include materials + labour)

Looking for someone experienced to repair scratches and damage on my internal door caused by my dog. The door has surface scratches, chipped paint and some deeper marks near the bottom hinge side. Would like it repaired so it looks neat again — patch/fill, sand, repaint, and blend with existing colour if possible. Please bring your own tools/materials. Located in Sydney. Flexible with dates but would like done ASAP. Please quote total price including materials. Photos attached.

Looking for someone to install a garden shed on a concrete slab and anchoring it to the slab. Dimensions are 3000mm x 1520mm Shed is a Absco Shed with anchors.

Need somebody to come & cut a damaged roller blind & then re attach the bottom rail, plenty of excess

Looking for someone experienced to repair scratches and damage on my internal door caused by my dog. The door has surface scratches, chipped paint and some deeper marks near the bottom hinge side. Would like it repaired so it looks neat again — patch/fill, sand, repaint, and blend with existing colour if possible. Please bring your own tools/materials. Located in Sydney. Flexible with dates but would like done ASAP. Please quote total price including materials. Photos attached.

Wheel on shower roller door is broken off, needs replacing (don’t have the wheel)

Install a curtain rod. Rod purchased new.

Rear double sliding door hard to slide and close

Need this installed onto door frame as per instruction booklet and photos. Drill needed!

Hi, I have started bagged rendering my single story brick house in the Megalong Valley. I have all the render and tools just need assistance to complete. Ideally you would have rendering experience and you would apply the render. I could mix up the render and assist. The job is ready to go and I am keen to get it completed very soon if possible. I think it’s a one or two day job

1 x door to be replaced Patch work & paint Bed side table to be assembled Under bed drawers to be assembled

I need to change 2 x door handles, both the holes through the door is too small. The hole for the handle and also the latch. I have the handles.

Fix a hole in the wall - plaster job

I have a wall mounted coat rack to install in a room and 2 x small clothes lines to install on the outside brick wall in my apartment

Looking for someone to assemble a small flat-pack metal garden shed (robot lawn mower shelter). Approx size: 97cm (L) x 92cm (W) x 63cm (H) All parts and instructions provided Needs to be assembled outdoors in backyard Ground is flat and ready This is a small unit but has multiple panels and screws, so experience with similar sheds or flat-pack builds is preferred. Requirements: Must bring your own tools (drill, screwdriver, etc.) Experience assembling metal sheds or flat-pack items Take care to align panels properly and ensure it’s sturdy

Hi, I’m looking for someone to fix and reinstall a manual window roller shutter/blind winder mechanism in 2 windows. The winder box has come apart from the wall and the internal parts (gear, spindle etc.) have come loose. The strap is still attached and running up into the wall, but the mechanism needs to be reassembled and securely mounted back onto the wall so the shutter/blind works properly again. Photos attached for reference. What’s needed: • Reassemble internal winder mechanism • Reattach and secure the unit to the wall • Ensure strap is working smoothly and winding correctly • Check everything is functioning properly I’m not sure if any replacement parts are needed ideally someone experienced with blinds/shutters or general handyman work. Flexible with timing but would like it done ASAP.