Find an experienced handyman in North West Melbourne

Floating shelf needs to be installed. The shelf is not pre-drilled, so drilling and mounting will be required. I would like the shelf to sit on a wooden support/base for extra strength and stability, rather than being mounted directly onto the wall. Open to suggestions on the best way to install this securely and neatly. Please bring your own tools and advise if any additional materials are needed.

Need to re laminate old kitchen. Benchtop,around stove and sink. Edges, and bottom. Around 4.3 sqm. Please see attached photos. Looking for a quote Flexible on dates and happy to supply or pay you extra to supply. The kitchen will be clean.

Hi there, I’m looking for an experienced handyman to help with two tasks at my home in Greenvale: 1. Wall-mount digital photo frame (15-inch) Mount a small digital photo frame on the wall It will cover an unused telephone socket Ideally make use of the existing socket for power (or suggest best solution) Neat, clean finish with concealed wiring if possible 2. Assemble IKEA Friheten three seat sofa-bed Brand new, just delivered Full assembly required Details: Location: Greenvale VIC Flexible with date/time (preferably tomorrow April 19) Please bring your own tools Experience with wall mounting and IKEA assembly preferred Budget: Open to reasonable offers (please quote for both tasks together) Let me know your availability and any questions. Thanks!

I can drop off and pick up the bike within 5km. Clean and lube chain, derailleur, bearings, brake cables. Adjust brakes.

Require render in small reaction of wall and few patch fixing

A few fly screen frames have broken and maybe some replacement of the actual fly screen themselves. We also have a window that's broken. The aluminium has parted away from frame that needs a bit of a Service.

Fixing door architrave that comes out

Repair door architrave that has been opend/comes out from the door handle end

Please provide a quote in your message. The renter has reported that the garage roller door is currently malfunctioning. The door needs to be manually pulled down, and when attempting to operate it via the remote control, the unit emits a continuous beeping sound without completing the closing function. This issue appears similar to one that was raised approximately five years ago, which your team previously attended to and resolved. Based on the current symptoms, it is likely a recurrence of a similar fault. From my initial review of the video provided, I believe the following may be contributing to the malfunction: Signal / Receiver Issue (most likely) The motor appears to have power; however, it may not be receiving the signal from the remote. Possible causes include: Disconnected or damaged antenna wire Fault with the receiver module (control box not communicating correctly) Interference from any added devices (e.g. WiFi/smart automation setup)

Rails on drawer broken. Doesnt slide properly and drawer itself doesnt line up properly either anymore. Lots of little beads fell out. I have collected them all.

My mixer on my tap snapped off and has come loose. I would need a tap replacement by a plumber. Please contact me for more info

Need handyman for installation for wooden bead (corner) x 10m Frame corner on sink slab x2m Blind replacement x 1 One small patch work job if you can do it. Wooden floor gaps filling / silicon as required ALL MATERIAL PROVIDED. ONLY LABOUR & TOOLS NEEDED.

Garage door no longer responds to remote controls or wall panel control. Have tried resetting remotes & limits but still no response. Model is Steel line SD-800

Sliding door to bathroom is jammed and needs realignment to allow smooth open and close. Every time I do it it reverts in a few weeks. Keen to find someone with experience in this issue

Roller door jams. Motor seems to work okay. Door just needs a shove to get it to open or close, so needs repair.

I need to get a pet door installed on a wooden laundry door. I will supply the pet door. Refer to the photos. Also there was a pet door before this and the last tenants have patched it. So we need to remove the patch and install the door.

I have two doors. One is already up but doesn’t close properly. I need it adjusting and I need a handle put on the door and drilled as it doesn’t have the hole at the moment. I also need my garage door put up. It’s an entry door fibreglass it needs to be put on the hinges and the door cut out for the hole and a handle.

Two small area for rendering

I have a few things to be done to a newly renovated property. I have skirting that needs to be installed it is about 10m worth, i need the top of a range hood boxed up, a bathroom door to be reinstalled.

Will need to hang door and install electronic door handle. Have hinges and door handle (door handle as pictured). Will need to trim door to fit