Find an experienced gas fitter in Melbourne

Our gas appliance pilot light stays on for a few minutes then shuts off by itself. The pilot flame looks weak — likely needs cleaning or a thermocouple check. Looking for a licensed gas technician or qualified repairer to inspect and fix it safely. Please bring your tools and check: Pilot flame / jet cleaning Thermocouple function Gas valve operation

"Looking for a licensed plumber to swap an old hot water system for a new Rinnai instant gas outdoor unit on the side of a brick house. This includes cutting redundant gas pipe on the old system at ground level and capped.(its exposed) Gas and water lines are within a meter. Job2:Also need 10 meters of sewer PVC pipe redirected at knee height into a 150mm inspection opening 10m away.(this is the kichen being redirected)

I need R-134a gas that is common for the fridge tanks- I need 22kg of this gas to fill out the tanks for my laser hair removal machines which they are using the same gas as fridge gas.

Gas main to bbq to be checked / cut off as bbq is being removed - pick up new toilet and install . Offer is to come and quote in Prahran .

Cut concrete form gas meter to veranda. Install new copper gas line from gas meter to existing ducted heater and stove (gas line is to predominantly be installed on timber weather boards/plinths). Re-instate cut concrete with new concrete. Remove and dispose of cut concrete and associated waste. VBA Certificate of Compliance (issued at end of works/project).

Licensed Gas fitter/plumber required to do the following tasks: 1. Connect 4 outdoor sinks wastewater to the IBC tanks. All sinks were operational previously with available pipes, parts (for inlet, outlet and waste pipes) and to be connected (to gas 9kg) hot water unit and pipe connections are from events previously working). 2. Do a gas safety audit for our vendors' gas cooking set up (numbers TBC but at this stage, around 15 vendors with most using 9kg LPG bottles allowing 15 minutes at most for each vendor, ensuring full safety & compliance) and liaise with the City of Melbourne team only if needed and ESV/BPC on the safety inspection day if required. (most likely require your attendance the first few hours of opening ie on 4/12, noting we open from 5pm on Thu 4/12.) 3. Our event preferred LPG installer - to be arranged and paid directly by the requesting vendors. Further details will be provided later.

The piezo ignition ignites the pilot light, which then ignites the gas burner, but the burner cuts out a second or two later. This seems to indicate a dirty or faulty thermocouple or a weak or misaligned pilot flame.

New Smeg appliances need instalation and old appliances removed and disposed of. I need a photocopy of your Electrical Licience and a Safety Certificare supplied upon compleation.

We smell a.lot of gas from the Indoor Rheem Hot water unit. Needs to be investigated for a leak.

After some assistance to have a gas oven disconnected before the electric oven is put in. Oven is free standing gas - if you can take it as well, that’s great. Not essential though!

I have had some kitchen renos and need. Gas stove reconnected. Also need new sink properly installed. Its in place but tap isnt secure and needs to be connected to water and drain etc.

Gas leak has been diagnosed by gas supply co but cannot fix because they told us its not on the supply side so we have to get our own plumber. They have turned off the gas at the meter so it is safe for now, but we can't use any gas appliances =(

I’m in Moonee Ponds and I need a new oven/stove connected and the old one disposed of by a qualified electrician.

We have a Vulcan Gas Heater and it does not seem to work when turning it on inside We believe the pilot might need to be lighted, but we are unsure on how to do this. The device does have an operating instruction sheet on it (image attached) Looking for someone who can come have a look and guide us on how to operate it Model: Vulcan C - X Gas Furnace 902

The cooktop is a 4 burner Smeg - only one is not sparking and cannot be used. The task is for the repair of the defective burner. Flexible with the time and date but I need it done sooner than later. Melbourne CBD close to Queen Victoria Market.

Need a qualified plumber and electrician to a. access and cut off gas and power supply to an old heater Job does not include removal of heater

Gas was cut yesterday and now hydronic heating unit needs restarting. Gas supply restored.

I have an electric 4 burner stove top and needs to be replaced with 4 burner gas top. Gas line is available underneath. Plumber will need to get gas fitting pipe approx 1.5 mtrs to connect the burner to gas outlet. The cut out is fit to size and the gas burner should slot it (already checked)

Need a plumber to cut a gas pipe and cap it off inside the brickwork so that the wall can be bricked up. The pipe is from an old gas heater that has been disconnected, but the pipe was capped outside the house.

Gas water heater - Rheen model 850330 Issue - hot water stopped coming. Checked unit and found continuous water dripping on the burner .. pilot light worked but didn’t stay on due to leaking water .. leak only stops when cold water turned off. Need to check the issue and quote for repairs