Find an experienced gas fitter in NSW

gas cooktop burner not staying lit the main burner malfunctioning repair if possible otherwise replace with new

Deliver a gas cylinder to restaurant in Newtown for outdoor heater

Gas fitting for food truck

I need someone to recertify my gas connection and provide a compliance plate as my gas provider will not supply gas without it.

Need to check gas leakage and fix Need to fix dishwasher mixture head pipe

Experienced handyman (better 2 workers) needed to overhaul an L-shaped polycarbonate multiwall patio roof. All premium replacement materials are provided by me (Laserlite H-bar/U-shaped gaskets, breather/sealing tapes). You provide tools and labor. Site Details & Heights: Roof Height: ~2.7m from patio / ~2.2m from raised garden bed. Ladders on-site: 1.7m A-frame and 4m multi-position ladder available. 10 Panels Total (11 vertical H-bars): * 1 panel: 0.84m x 1.85m (Far left, needs bad DIY redone) * 3 panels: 1m x 1.85m * 5 panels: 1m x 3m (Deep section) * 1 panel: L-shape transition junction **Scope of Work:** 1. **Disassembly:** Remove 11 aluminium H-bar caps and old gaskets. Shift panels as needed. **Crucial:** You MUST bring your own structural plywood/crawling boards to bridge the 1m timber beam gaps and walk across the 3m spans. Do not step on plastic. 2. **Clean & Dry:** Pressure wash dirt/algae from internal panel channels using a mild bleach solution. **Mandatory:** Use a leaf blower/heat gun to dry inside the hollow channels 100% bone-dry before sealing. 3. **Trim & Tape:** Top edges get white Sealing Tape. The current bottom aluminum trim is a single long bar causing buckling. You MUST bring an angle grinder/hacksaw to cut it into 10 separate short sections matching each panel's net width (leave 3-5mm expansion gaps). Apply mesh Breather Tape, fit rubber U-gaskets, and press cut trims over them. 4. **Reassembly:** Thread new gaskets full-length into the 11 vertical caps so they compress tightly against the bottom end-caps. Slide panels under house flashing and screw down tightly. **Tools You MUST Bring:** * Plywood / crawling boards (essential for 1m spans) * Aluminum cutting tool (Angle grinder/hacksaw) * Pressure washer & Leaf blower/heat gun * Cordless drill with 5/16" hex socket https://www.justritestore.com.au/assets/Brochures/2024.0689-Multiwall-Brochure-Update-2024web6485.pdf see this diagram

outdoor kitchen gas burner doesn't spark fire when switched on, i need to use a lighter next to it to do so.

The gas stove burner doesn’t stay lit. It lights briefly when the knob is pressed but goes out as soon as the knob is released. Brand is artusi

licensed gas fitter: 1. Confirm the outlet is still connected to natural gas. 2. Pressure-test the bayonet valve for leaks. 3. Replace the bayonet socket if it’s worn. Advise best heater for house and install

Licensed plumber required Decommission/remove gas outlet, close off and put beneath floor. Close off pipe which has been accidentally cut and runs from the mains (pipe is black plastic) Located in Balgowlah.

Old house, the feed in pipe from the gas mains goes in through a window which I'm getting repaired so want it to trace along an inside wall, I'll even pre drill the route. To me it looks simple but I'm not confident about gas work, Check out the photos and hit me with a quote.

Install a gas bayonet taking gas from inside kitchen cabinet wall to outside of same wall facing lounge room. It's a straightforward job, minimal distance to run. It's for an unflued gas heater. Easy access.

I need to disconnect combi oven, char griller, and deep fryer from my shop at haymarket and move it to other place on CBD

Hi there, I need a licensed NSW gas fitter to rectify a gas installation defect identified by Jemena on my property in Eastwood. The defect noted on the certificate is: "Earth stake & weep holes in exclusion zone". Scope of work: Relocate/extend the gas regulator vent line or pipework to ensure it is clear of the electrical earth stake and building weep holes (per AS/NZS 5601.1 standards). Perform a pressure/leak test upon completion. Issue a formal Certificate of Compliance and a Leak Test Certificate as required by Jemena. Please refer to the attached photo of the Jemena Non-Compliance notice for exact details. Must be fully licensed and insured in NSW. Please provide your license number when offering. Flexible with timing but needs to be completed within the next few days. Thanks!

We would like a licensed gas fitter to check where the gas leak is in a commercial kitchen. Please put down your offer and when you can come and inspect.

My cooktop gas jets needed to convert from natural gas to LPG.. can you provide quote for the same. https://lpgjets.com/en-au/collections/bosch/products/bosch-pbp6b5b60-4-burner-gas-hob-lpg-conversion-kit Cooktop models: PPS9A6B91A PCR9A5B90A

Need a gas heater connected to an existing bayonet point in my downstairs living area. Please quote a fixed total price including connection, safety/leak test and any required fittings. Photos of the bayonet point are uploaded. Please ensure the work is carried out by a licensed gasfitter and is safe and compliant.

Have a new gas cook top already installed, but just needs to have the conversion kit applied to go from Natural Gas to LPG. I have the conversion kit already, just need the install done

Need 1 gas stove burner to be repaired (see photo). When turned on, the fire doesn't stay lit. Other 3 works fine

Gas Cooktop Repair – Gas Valve Stuck Open One of the gas burner control valves on our cooktop has failed and is stuck in the open position. The affected burner is the top right burner. When the gas supply is turned on, gas flows continuously from this burner regardless of the knob position. For safety, the gas has been isolated at the mains. Looking for a licensed gas fitter/appliance repair technician to inspect and replace the faulty gas valve (or advise if another repair is required). Please provide a quote