Find experienced local fencing contractors near you

Tidy up down the boundary line about 20 metres long by 1 metres width and then erect temporary fencing which is already on site .Allrubbish / waste to be left on site . Type of gardening: Other Size of garden: Under 50m² Has green waste bin: No

Garden gate damage needs to be fixed, brackets are broken so the gate is not attached properly.

I would like to build a wired/tension wire fence with post for my garden bed so that I don't hit the hydrangeas whenever I enter and exit my garage when where are in full bloom. I would also like be able to put some shades when the sun is very so that they won't wither early. Maybe some trellis at the back so make it more easy on the eye. I would be the one who will buy the materials from the design the will suit using the picture attached.

Repair and reqire fence. Move star pickets to tidy shape of garden first

I will be purchasing a gate from stratco nee someone to install the gate its 108cm wide by 1.8 high attach to a bric wall.and the beick house .its a picket fence aluminum. Will have the wall brackets. The gate shown is like the one being put up bit nit the actual gate as i babe to go picke it up

Come my house to look, give me quote for fence

1. remove two trees: 1m and 2.5m high. 2.remove soil next to the fence and replace plastic garden edge with three 2.2m steel edges(height 25cm, 40cm, 55cm). 3. replace 2 pieces of timber fence palings

I need a welder or metalworker to replace the two hinges on a wrought iron garden gate. This budget is for labour only. I will supply and pay for the hinges and fixings separately. Please do not include hardware costs in your offer. The gate: Single leaf, approximately 2 metres wide Open picket style, estimated 40–80kg Both the gate frame and the gate post are hollow steel square tube Street-facing front gate on a brick pier Existing hinges are old hand-made welded barrel hinges, rusted and worn Photos are attached — please look at them before making an offer. Scope of work: Support the gate, cut off the two existing welded hinges and grind the surfaces flush Weld the gate-side half of each new hinge to the gate frame. Tack weld and check alignment first, then complete the welds using a staggered sequence to avoid distortion Mark out, drill and bolt the post-side half to the hollow post using through-bolts with backing washers or plates, or rivnuts — not self-tapping screws alone, as the top hinge carries a tensile load Check the gate swings level, closes correctly and does not scrape Clean the welds and touch up all bare metal with cold galvanising primer and a matching topcoat Hinges: I will supply weld-on / bolt-on gate hinges rated to at least 150kg. Please tell me in your offer: What fixing method you would use on the hollow square post Whether you need me to purchase any specific bolts, rivnuts or backing plates so I can have them on site before you arrive I have a second gate of the same type. If this job goes well I will book you for that one as well — you are welcome to quote both leaves together if you prefer. Requirements: Own MIG or stick welding equipment, plus angle grinder, drill and metal drill bits Access to power, or your own generator Demonstrated experience with gate and fence welding — please mention similar jobs in your offer

Need a wire lattice backing or similar built for plants to climb

Have an outdoor gate that has rusted through hinges, need some with the skills to replace with new hinges

Remove foliage that is leaning on the fence, make fence upright again. I am assuming reusing the existing fence, maybe a couple of verticals posts need replacing

Garden bed fence needs to be rebuilt. You will see from the pictures and before and after removal of the existing fence. Altogether the length of the fence is 11.5 meters and two railway sleepers high. There one exception to this where the grounds is at an angle and might required 3 sleepers. I need a nice professional finish.

The gate to my chicken run keeps blowing open because the latch is dodgy. I'd like someone to either fix or replace it so the chooks are secure.

Need to build a garden gate, please send photos of jobs you have done before.

Looking for a handyman available soon to realign and fix back gate. It is a small colourbond gate that closes. The end of the frame was screwed into a brick wall but one of the bolts snapped off. New hole in brick wall was required that I didn’t put at the right height and made a bit of a mess of so the latch won’t close. I have run out of time and don’t have the right tools for the drop before I head away tomorrow and need the gate to lock. A quick handyman job if you’ve got a drill. Have new plugs and bolts. Extra points if you’ve got some extra time and are available to rescrew my garden shed door so that it also closes. (Can raise price of job if required).

Looking for someone handy to do a very basic, low-cost repair to an old timber boundary fence and remove the pile of branches/garden waste shown in the photos. My budget is genuinely quite small, so I am not looking for a new fence, professional restoration or anything cosmetically perfect. I just need someone to: * Push/straighten the existing fence back roughly into position. * Secure it so it isn’t leaning into the neighbour’s property. * Close up the larger gaps so my young kids can’t get through. * Screw/nail existing timber back together where possible. * Patch any obvious gaps with old/recycled palings or inexpensive timber if needed. * Remove the pile of dead branches and garden waste. * Leave the area reasonably tidy. Please reuse as much of the existing fence as possible. Second-hand/recycled timber is completely fine. I don’t care what it looks like as long as it is reasonably secure and safe. I understand the fence is old and this is only intended as a temporary/basic repair. Very limited budget – please only offer if you’re happy to come up with a simple, economical solution.

Repair the garden barrier see pic in hallam today

The gate doesn’t latch shut anymore and will need fixing

I have an existing garden fence panel that needs to be moved circa 400 mm back to its original location. Accidentally moved during a renovation and bow blocks the electrical meter. Holes from original location already there, fence just needs to be taken down then moved back Can be done any day before 29/06/26. Probably 1 hours work. Back gate will be unlocked, no one will be home

Frontyard fencing and garden gates replacement. Please see attached.

We can supply all the equipment to build a dog wire fence and are looking for someone to come and actually build it. It is for our front fence line and is approx 150 meters in length. There is an old 3 wire / star picket fence at the moment and we are replacing this with dog wire

Remove a light wire pet fence that has the posts cemented into the ground. It would be better for the fence posts to be taken out of the ground as I fear if we cut them at ground level the kids will cut their feet on the steel

I’ve bought a hidden fence for our beagle Just looking to set up properly in back yard

I need a secure barrier installed along the base of my existing fence to prevent my dogs and the neighbour's dogs from being able to make contact and/or dig through. There are 3 sections (as per photos): 4m of gravel and 2 garden beds of 4.8m (on a steep slope) and 3.9m. I'm open to recommendations on the barrier type. Quote is for labour only - materials reimbursed separately.

Hi, I’m looking for someone experienced in fencing installation to install a garden fence at my property around Killcare on the Central Coast. The purpose is to create a secure area for our dog and chickens. I have already purchased the main materials, so I’m mainly looking for labour and installation. Fence: • Approximately 30m of fencing • 1.2m high Jack Pro Series Heavy Duty Dog Mesh, already purchased • 15 × 1.7m steel fence posts, already purchased • Posts approximately 2m apart, adjusted as needed • Posts to be driven approximately 50–60cm into the ground • Mesh securely attached to the posts with galvanised tie wire • Bottom of mesh needs to be secured well to prevent the dog digging underneath. (haven't bought anything yet, but looking for recommendation on the day) Important: the land is NOT flat. The garden is uneven and slopes in places, so the fence will need to follow the existing contours of the land rather than being perfectly level. Experience with mesh fencing on uneven/sloping ground is preferred. Gate: • One access gate, approximately 80–90cm wide and 1.2m high • Gate with its own two posts • Secure latch so the dog cannot open it • Happy to use a suitable ready made gate or framed mesh gate Materials already purchased: mesh, 15 steel posts and galvanised tie wire. I can purchase any additional brackets, anchors or gate hardware required. Please quote labour only, ideally with a site visit before confirming the price. I can provide photos of the area.

Mesh enclosure + lockable double gates to the two open sides of a paved bay under my porch roof. The other two sides are existing brick/rendered wall. Photos and 3 dimensioned diagrams attached. DIMENSIONS (confirm on site) Street side, fixed mesh: 3100 W x 2510 H Entry side, clear gate opening: 1550 W x 2510 H Approx 11.5 sqm of mesh. SPEC Frame: RHS 50x50x2.0 minimum, upsize if your design needs it. Mesh: 50x50x4mm galvanised weldmesh, welded to the frame. Street side: full-height fixed panel, no opening, three uprights (both ends + mid-span). Entry side: two swing leaves approx 775 each spanning the full 1550, no fixed infill above or below. Posts: 5 uprights. The two street-side end uprights anchor to the brick wall and corner pier (no footing). Mid-span post and both gate posts each need a concrete footing - 3 minimum. Gates hang on posts, not masonry. Gate hardware: weld-in lock box or heavy-duty hasp; drop bolt into floor socket on passive leaf; welded/non-removable hinge pins + capture stud; adjustable hinges; max 15mm bottom clearance; must open from inside without a key. Confirm swing direction at the measure. Finish: powder coated or pre-painted charcoal/dark grey. Cold-gal all welds and cut edges. Bottom rail: plain straight RHS, mesh terminating above it. Build to existing paver level. SITE Floor: loose pavers on sand. Per footing, lift 2-3 pavers, dig 300-400mm, pour, reinstate. Both gate posts sit near the paver-to-slab junction - tell me how you'd found them. Walls: anchor into brick units, not mortar joints. Chemical anchors may be needed. Soffit: lined sheet. Locate joists/battens, or make the frame self-supporting. Services: wall-mounted equipment and conduit inside the bay must not be obstructed or built over. QUOTE All-inclusive: measure, materials, fabrication, finishing, transport, labour, footings, paver reinstatement, waste removal. Bring your own tools. Please include your NSW contractor licence number. Weekend install preferred.

Approx 20 m temporary fence to keep dogs safe while boundary fence being replaced

We need a baby gate installed upstairs and was hoping to have a custom wooden gate built and installed for in the entry hallways of our house

We bought a fence from Bunnings and to fit it, it is needed a few holes on the wall to install properly.

ideally would like a fence that is not a permanent structure as we are renting so that our dog does not escape possibly would also like to cover up cables and pool pump so he does not have access

All material supplied to install dog wire and star picket fence to back boundary - 49m long Already marked out and sprayed. Is in the bushy area though easy access

We need someone to come and measure two areas for dog gates. Area 1: pantry (will likely require a tall and narrow gate). Our dog can jump high gates, so the taller the better here. Area 2: outdoor dog gate from garden to deck entrance. Once again, need it to be tall, but might be limited by height due to size of stairs to connect it to. We will need someone to come and inspect the areas, to measure them, and then go to purchase gates (we will provide the cash for this as a separate payment not included in the job task). Following that, you’ll need to return to fully install the gates. See images for details..

Need to design and install fence or gate for dog near laundry Photo provide regarding area If want can come and take dimension Roughly 1-1.2 m width and. 1.5 m height

Oscillot cat fence Roller required to be installed. Small backyard (10 Meter)

Hi, I’d like someone to cut one of the vertical bars on this pet gate so that my cat can get through, but my dog can’t. * Bar diameter: 13 mm * Cut the bar at the top and bottom * Sand/grind the cut ends so the frame is flat and smooth Preferably someone in the northern suburbs. I’m happy to drop the gate off and pick it up. Please let me know if you have the tools and can do this. Thanks!

Gate is catching, making it a little difficult to open the pedestrian gate.

Looking for someone to install a Sureguard Pingg-String cat containment system on the timber paling fence at my property in Augustine Heights. Total fence perimeter is approximately 58 metres. All components have been purchased and will be provided on the day. This includes insulated cable, extension kits, end post kits and energiser included. The job involves mounting bracket arms and insulators along the top of the fence, running and tensioning the wire angled inward toward the yard and rigging the gate loop over the single gate. The energiser position will need to be assessed and decided on the day based on what works best for the setup. It needs to be installed in a north-facing position with access to full sun. There is one fold-down clothesline mounted to the fence that will need the wire routed carefully around it with extra insulators either side to avoid contact with the metal frame. No drilling into structures required as all fixing is into timber palings. Happy to be home on the day to show you around the property before you start.

Need someone to put up a temporary mesh fence along my back boundary approx 30 m

Two gaps tightly filled in the fence line

I need a dog gate for my side yard. House is hebel and fence is timber. We had one done for inside the house and if you can do something similar for the side yard that would be amazing

Build a colourbond gate 1.5m wide in this space

Im just looking at getting quotes done for installation of colorbond fencing in my backyard. The length is 18mtr as per right hand side of the picture

Colorbond fence needs a bit of love. Needs - 2 sets of aluminium posts removed and replaced. - 2 steel post installed for colorbond gate - all existing sheets to be reused where possible. This is for labour only as I will purchase the supplies

Please see photos on what’s required for the fencing.

Repair 2 panels of colourbond fence

Replace and install 2 colourbond sheets on the fence panel We have already supplied the sheets, literally need to unbolt the top section of the fence panel, slip the old ones out and slip the new ones in Offer to take the old panels to the tip, or leave them there and send me a photo.

I want to cover this space with a colourbond gate and fence panel. Will need to cut in hole in fence panel for electrical plug

Replace colour bond fence upright

Actual colourbond gate needs to be placed back on existing frame

A few panels of my colourbond fence have come off. I'm missing the bolts for them. They're very finicky and they will probably require new bolts/screws to be set in place.

Experienced Landscaper/Fencer Required – Colourbond Fence I’m looking for an experienced landscaper/fencer to supply and install approximately 50 metres of Colourbond fencing, along both sides of the house. Job details: * Approx. 50m of Colourbond fencing * Both sides of the house * Approximately 1.8m high * Supply and install posts, panels and concrete * Neat and professional finish required * Experienced landscaper/fencer preferred * Please provide your quote, availability and examples/photos of previous work * Labour and materials to be included in the quote Please only apply if you have solid fencing/landscaping experience.

Need corner colourbond sheet brought, cut and attached to the current one to raise height just in the corner. Needs to meet compliance of 1.8m above garden bed. Thinking a triangle neat and matching the current. Offers welcome, no idea on costs exactly

Small section of colourbond fencing to be installed. I believe the colour is shale grey (to match the other fence) Dimensions are 2.1m x .840m. 1 x post will need to be concreted in and the other can be attached to the brick wall. Looking to get this done next weekend. I'll remove & dispose of the old fence.

One piece of colorbond fence to be placed back up

supply and install 3 gates on side yards - each is 900mm and supply and install 2 panels almosy 2 meter each panel of fencing

About 5 or so I’m unsure how to estimate the colour bond fence sheets to be replaced Colour bond fence side gate to be fixed with latch I have the brand new latch

Remove existing colorbond panels. (7 sections) Remove pine sleepers. Install concrete sleepers. (Delivery coming Monday morning) Re-install same colorbond fence panels. (Same as in the photo) No materials needed and NOT disposing of the pine sleepers we will take them away. Must be confident in installing fence panels. Area Hinchinbrook

Handyman Needed – Colorbond Pool Fence Repair Looking for a handyman experienced with Colorbond fencing to close a gap in our pool barrier so it can pass a pool safety inspection. Work required: Fully close the existing gap so it cannot be used as a foothold or climbed through. Finish the infill at a 60-degree angle so it is deemed non-climbable Use matching Colorbond sheet, flashing, cover strip or suitable infill for the whole fence panels length (or 30cm inside pool area and 90cm outside pool area) Securely fix to the existing posts/rails with a neat, professional finish. Supply all materials. Colour: Burnished Copper preferred, but black is also fine. Please only apply if you have experience with Colorbond fencing and pool barrier repairs. Photos attached.

- I have a gap at the back fence and need to be fixed. One panel is also damaged so it needs to be changed. - Have some left over colorbond sheets to provide. However, they might need to be cut to fit to size.

You are quoting to install 8 x extension panels on top of colour bond fence My fence is the cottage green one. Photo of extension panels from Screenline pic attached. I already have the 8 x extension panel kits from Screenline.