Find trusted local electricians in NSW

I’m looking for a qualified electrician to swap the existing ceiling light fittings between two rooms in my home. Scope of work: • Remove the ceiling light fitting from Room 1 • Remove the ceiling light fitting from Room 2 • Install Room 1 light fitting in Room 2 • Install Room 2 light fitting in Room 1 • Ensure all wiring is safe, compliant, and secure • Test both lights to confirm they are working correctly Details: • No new light fittings required • Standard residential ceilings • Easy access to both rooms • Power can be turned off at the switchboard Requirements: • Licensed electrician • Own tools • Able to complete in one visit Please provide availability and a quote. Thanks!

I am looking at getting outdoor power points installed in 2 locations. In the image location A, and location B. Location A (just below main switchboard)- 1 x dual 10amp outdoor outlet 1 x 3 phase 32A outlet Clipsal Easy56 (for portable EV charger) Location B - 1 x dual 10amp outdoor outlet (there is another power point on the opposite side of the wall in the lounge room). Also replacement of 2 x faulty light switches ( I have the replacement light switches on hand) I will be providing the 3 x power outlets, so i only need the installation costs. Thanks

Electrical fix , plus whirlybird replacement

We have tablet on the wall the tablet has fallen on the floor and broken. When that happened the end of the cord got stuck in the tablet and broke. The other end of the cord is in the wall. We need to attach a new cord

You need knowledge of KINGS products! I’m looking for a qualified van-conversion electrician to inspect my power setup in my van. I recently had a Kings power converter installed for a 200Ah lithium battery, but shortly after installation smoke came out of the unit. I immediately stopped using it and haven’t touched the system since. I need someone experienced to: Inspect the Kings converter Check the wiring and overall setup Identify what caused the issue (faulty unit vs installation) Advise whether it’s safe to use, needs repair, or needs replacing ⚠️ai’m specifically looking for someone with real experience in van electrical systems, as this is a safety-critical system and needs to be done properly I can come to you!

Need an electrician to fix a few switches with 2 way lighting control, convert a 6 gang switch to a 4 gang switch x 2 and replace outdoor lighting that short circuits.

The table lamp shown in the photos has stopped working, and I’m not sure what the cause is. You can see the brand name in the pictures. It is controlled by a small rotary dial that adjusts both the power and the brightness. I am looking for an experienced electrician or handyman to troubleshoot and fix it.

I need a licensed electrician for 3 tasks in my converted garage (6m × 6m, 2.7m ceiling). There is a bedroom directly above, so vibration prevention is critical. TASK 1: Install new ceiling fan + WiFi module (Garage) Supplied by me: • Hunter Pacific Aqua V2 IP66 DC 70” (Matt Black) • Hunter Pacific WiFi Smart Module (v2 fans) Requirements: • Must mount into a ceiling joist OR install noggin/bracing • Power can be taken from the existing ceiling GPO/outlet used for the garage door opener (preferred) • Tighten everything fully and run test at speed 8–9 for 5–10 minutes • Confirm no wobble/rattle and minimal vibration transmitted upstairs • Confirm remote + WiFi both work TASK 2: Install 12 downlights + install dimmer (Garage) Supplied by me: • 12 x LED downlights • 1 x LED dimmer Requirements: • Remove the 2 existing tube lights • Install 12 downlights • Install the dimmer switch in place of the current standard ON/OFF tube-light switch • Ensure dimmer works smoothly (no flicker/buzz if possible) TASK 3: Earthing check for 4 existing fans (Quick test) There are 4 existing ceiling fans already installed and working (previous installer). Please perform a quick earth continuity / earthing verification for all 4 fans (should take ~5 minutes for each fan as they are working and functional).

Light shorted out need electrons to fix it

2 light switches in bathrooms replaced

The switch button is loose, 3 of them

Replace broken light fixture on outdoor wall with Phillips Hue outdoor smart light. No earth cable in the current light fixture but needed for the Phillips Hue smart light

Looking for an electrician to install an IKEA pendant light

Hi I need someone to install an outdoor power supply socket in the wall twin switch. I have one inside the building, and need outside point just at the back of it. So no need for any wiring etc. I have attached photos, could explain. Its a sparky job, would prefer you are certified and you supply that outdoor plug twin switch. So please provide your quotes with labour and material separation. Thanks ( if price is good then there is another similar point on the other end of balcony. I would include that too)

My old split system unit has stopped working properly. The fan works but when I put on hot or cold setting it works for a few seconds and then trips at the fuse box. Need it fixed. House - single story.

looking for qualified electrician with insurance to reconnect NBN wires to the socket All parts are provided and intact, very quick job

Hello, We are looking for a licensed NSW Electrician to attend our retail store, in Newtown, to replace three faulty ceiling downlights. The Issue: Three recessed LED downlights on our main sales floor are out and no longer illuminate. This is affecting the overall brightness and professional presentation of our store. The Job: The task is to supply and install new replacements for all three faulty lights. The scope of work includes: 1. Safely accessing the light fittings in the high ceiling (approx. 3.5 meters). 2. Removing the three old downlight fittings. 3. Supplying and installing three new, suitable replacement LED downlights and/or drivers. 4. Ensuring the new lights' colour temperature and brightness match the other existing lights. 5. Testing the new lights to confirm they are fully operational. Light Specification (for sourcing a match): - Type: LED Downlight Deco, 13W Round, White, Dimmable, Warm White (from GoLights). See attached spec sheet. Requirements: - MUST be a fully licensed and insured NSW Electrician. - You must have your own tools, including an A-frame ladder or platform appropriate for a 3.5-meter ceiling height. - Experience with commercial lighting, particularly recessed LEDs, is essential. - The contractor must be able to supply the three replacement downlight fittings. Location & Timing: Location: 229 King Street, Newtown, NSW 2042. When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a comprehensive quote for the complete job. Your offer should include all labour costs AND the cost of supplying three new LED downlight fittings. Thank you.

We are trying to demo our kitchen but need to remove a few power points before we can get rid of the cupboards safely.

Installation of split system ac 7kw in Mount Druitt replacing an old one.

Bathroom: replace switch panel with 3 switches (light, heat lamp and fan) Hall: replace power point (2 socket) Dining: replace power point (4 socket) Bedroom 1: relocate light switch to other side of door Bedroom 2: relocate light switch to other side of door. Gyprock has been removed behind hall and bathroom walls, meaning cabling is visible and accessible.