Find local air source heat pump installation & repair in NSW

Evoke heat pump dryer door catch not working . The door does not close gives an dop error. Looking for someone onsite to come and fix it. Photos can be provided if required.

Samsung heat pump dryer stopped working mid cycle, and wont start again. Need help fixing it

Unpack Move and Install Haier Front Load Washer and Heat Pump Dryer

Hi, I’m looking for an experienced appliance technician to diagnose and fix my Bosch heat pump dryer. Appliance * Bosch Serie 8 Heat Pump Dryer, SelfCleaning Condenser * Model (E-Nr): WTW87564AU/09 * Installed in laundry, front access Issue * Dryer completes the cycle normally, but clothes are still damp at the end * Drying performance has dropped compared to before * No obvious error code, just poor results What I have already done * Removed and washed both lint filter inserts and refitted once fully dry * Cleaned lint around the filter area as best as possible * Unit is plumbed to drain via hose into the sink (not using the tank) * While at some jobs seems to do a good job, most are still damp What I need * Full diagnosis of the cause (airflow restriction, moisture sensor reading, fan/heat pump performance, drainage related self-clean issues, etc.) * Clean and service internal areas if required (I understand “self-cleaning condenser” models can still build up fine lint internally) * Confirm correct operation and advise if any parts are needed before proceeding Please include in your offer * Your experience with Bosch heat pump dryers, ideally Serie 8 * What your call-out includes (inspection, cleaning, testing) * Any call-out fee vs labour rate * Earliest availability * If parts are needed, please quote parts separately before replacing anything Location * Caringbah, NSW * Parking available: Yes Timing * Flexible, but I would prefer ASAP.

I believe it may be the drum or belt that’s faulty. The dryer is not spinning when I turn on the load so the clothes remain wet.

LG heat pump dryer is working fine but it makes noise when I spins

supply n install heat pump hot water unit

My Yokohama 8kg heat-pump dryer is malfunctioning. The drum will not rotate although other functions seem to be ok. Model is YOKHP80W.

Replace existing 350L outdoor electric hot water system (postcode 2223).Upgrade to a 270–315L heat pump system. Please provide a quote for supply and installation, including ESS and STC rebates.Prefer a like-for-like replacement in the same location.

The heat pump dryer is turning on but not spinning after a wet heavy load was attempted to dry.

We have a water heat pump system at the back of the shop. The outdoor unit with fan and compressor is attached on the wall, but needs to be moved 30cm on the right as it is overlapping on the neighbour so part of the wall. Please note the unit has refrigerant gas lines that would need déconnexion.

Service hot water heat pump

We need a Britec adjustable dryer stand assembled (easy) and need our 50kg heat pump dryer (heavy) placed on top. It is going in a tight space but I’ve measured everything so it’ll fit perfectly.

Bosch Heat pump dryer There’s a sound coming when I turn on the dryer. Need it checked out a fixed

Servicing of Samsung heat pump

I have heat pump ducting pipes for the ducted aircon going inside wardrobes. I need these covered by a board (MDF panel) so that this is hidden. Dimensions of the pipe : Top part - Length - 46.5 cm Breadth - 14.5 inch (37 cm) Depth - 14.5 inch (37 cm) Bottom part - Length - 76 inch (193 cm) Breadth - 14.5 inch (37 cm) Depth - 14.5 inch (37 cm)

Compressor and fans run. Indoor air sometimes cools but operation is unstable. Large/suction pipe stays warm in cooling; small pipe can get quite cold. Unit switches correctly into heating, but struggles to return fully to cooling. Previous actuator / reversing valve issue for zoning fixed. Suspect mechanically sticking reversing valve. Looking for diagnosis and quote for repair vs replacement.

Moving a heavy heat pump dryer (60kg) downstairs to my internal garage

Change out PCB boards on hitachi heat pump (I have ordered). Work through boards to see which is faulty and replace. (I get a refund for unused/unopened boards

I’m looking for a licensed electrician to install an outdoor weatherproof power point for a new heat pump. Scope of work: • Install 1 x outdoor weatherproof GPO (power point) on the external wall in the location I’ll show you. • Existing internal power point directly behind the desired location, and • Another existing power point approx. 10 metres away on the same wall outside. • Power board is 15 meters from the desired spot. Preferably a dedicated/isolated 15A power run via conduit from power board, which is approximately 15 meters away. • Outdoor power point unit will be supplied by you. • You to supply all other materials: cable, conduit/trunking, fixings, etc. • Test the circuit, ensure it’s RCD‑protected, and provide any required certificate of electrical safety/compliance. Requirements: • Must be a licensed electrician (please include licence number in your offer). • Experience with external/weatherproof power points. • Clean, tidy work and must make good any small penetrations made. Timing: • Flexible on day and time – ideally within the next 1–2 weeks. Please let me know: • Your approximate total price (labour + materials, excluding the power point itself), and • When you’re available.