Find local NBN electricians in NSW

Install 2x30-40A Power Lines + Optical Drop + Network Cable to Backyard - Edmondson Park Licensed Level 2 ASP + Electrician needed. Professional, compliant, insured work only from 3-phase meter + NBN cabinet. Exact Scope: Run/install 2x 30-40A power lines from 3-phase meter to backyard (connection may already exist - verify/confirm first I need this to power my server rack and need some grounding for the rack too Install optical drop (fibre (sfp attached)) from inside the house NBN/security cabinet to backyard Run Cat6 network cable from same NBN/security cabinet to backyard All work AS/NZS compliant, fully tested + certified Provide compliance certificate Location: Edmondson Park (exact address on booking) Requirements: Level 2 ASP licence for NBN fibre work Fully licensed/insured A-Grade electrician Experience with 3-phase power + optical drops Photos of existing 3-phase meter + NBN cabinet provided to selected tasker Need a regular power point dropped in the jist behind the rack.

Electrician to run nbn data cable from garage to house through ceiling

We had our journey accidentally cover over our nbn cable and need a whole cut in the plywood to get cord to connect internet

Updated scope:Revised from6A to Cat6, with 7 runs, a mini patch panel, PoE camera mounting, and NBN FTTP conduit/draw wire pre. Looking for an ACMA registered cabler for a domestic networking job in a single-storey house. Scope: - NBN FTTP conduit / draw wire preparation: Prepare or use a suitable conduit with draw wire from the Far Wall entry area to the Garage Near Wall, approx. 6–7 metres. The Far Wall has no power, so the NBN box needs to be installed near the existing power points on the Near Wall. NBN FTTP is not yet installed; this is for the NBN technician to pull fibre later. - 7 x Cat6 data runs, all terminating at the Garage Near Wall: - Lounge x2 on one double RJ45 wall plate: - 1 x Lounge-WAN / NBN to Router - 1 x Lounge-LAN / Router back to Switch - Bed 4 x2 - Bed 1 x1 - Bed 2 x1 - Front door CCTV x1 for PoE camera - Garage termination: Install a small Cat6 mini patch panel at the Garage Near Wall, preferably 8-port or 12-port wall-mount type. - CCTV: Mount 1 x PoE camera on the eaves near the front door. Please include drilling, mounting and basic weather sealing if required. - Materials: Please supply and install solid copper Cat6 cable, RJ45 wall plates, keystones, mini patch panel, labels, conduit/draw wire materials if required, and all fixed cabling materials. Please do not use CCA cable. - Testing and labelling: Label both ends of every run and perform basic testing on all Cat6 runs. Please provide photos or test results showing each run has been tested. - Hardware supplied by me: - Switch - Router - PoE camera Requirements: - Must be ACMA registered and insured - Upon completion, please provide a completed TCA1 or equivalent - Please confirm the 6–7m NBN conduit/draw wire preparation from the Far Wall to the Garage Near Wall is included in your quote - If any additional work is required after inspection, please advise before starting

Need electrician to move NBN connection point from bedroom to living room. Move is about a 1m but need to take cables to different wall and put in the tall boy in living room.

I had NTD box installed downstairs in garage by NBN however I required a licenced insured electrician (deals with NBN) to drill a hole through the concrete slab ceiling with a diamond tip drill and run a Ethernet cable from the NTD box to my modem upstairs

Four tasks: 1) Replace NBN battery - the replacement battery has already been purchased, just needs to be installed. 2) Awning window gets stuck and doesn't fully close 3) Help assemble flatpack desk furniture 4) Help assemble outdoor chair

I need an electrician with ACMA for two quick tasks at Jannali. 1. NBN HFC Repair (Priority): I accidentally cut the two coaxial cables (In/Out) inside the external NBN PCD box. I need these re-terminated with F-Type compression connectors and reconnected to the existing CS-4002 isolator. (I have all the parts, just need the ends crimped). 2. Outdoor Light Replacement: Replace one existing hardwired outdoor light with a new unit from Bunnings (already purchased). It is a straight swap onto the existing wiring.

The NBN cable does not have a proper cap on it, so the wire is exposed and comes out of the port easily. Please supply the proper cap and install on the cable, ensuring it plugs into the NBN port.

Hey I just get the nbn connection into my place , so I need to install a HFC socket witch is coaxial cable , I live in jannali 2226

I need to reinstall my NBN FTTP box (NTD) on the wall. The box is already onsite. It just needs to be mounted and connected. No battery backup unit required. No NBN technician required – only physical reinstall. Tools for wall mounting required. Flexible with day and time.

Install 2 x OVERHEAD CABLE POSSUM CRITTER STOPPER GUARD ROLLER KIT ( supplied) to 2 NBN lines coming into second story level of house - at dusk when possum has left roof

Want to move nbn connection to directly underneath the house so it is out of site. Right underneath where it currently is is a storage unit that is easy to access - it can be moved in to there

Need a certified technician to install an RJ11/NBN wall socket for internet access. The apartment only has an old 600-series telephone terminal. There is no modern RJ11 or NBN-ready socket installed.

We have just moved to Nashua and in need of someone to help connect our Wifi with Telstra, please (UniFi modem). Would love to have this completed today or tomorrow please. Thank you!

Nbn access point in bedroom Move to living room or install extend ethernet cable to living room.

Looking to move my security system NBN box through the room right next door

I need the nbn fiber conduit on side wall of my house rerouted as shown in attachment. Existing length is ~9 meter

I’ve noticed multiple ethernet wall ports around the house and would love to have my NBN connected this way to avoid wifi issues. I have tried myself but can’t seem to figure it out

The wall socket our modem plugs into is old and is not connecting. Want to replace with the Ethernet wall fixture.