Find a professional gate installation in NSW

My automatic sliding gate stopped working. Only click sound , while pressing the button. Need to fix asap.

I need an electrician to hardwire a recently installed automatic gate, which is currently running off an extension lead from an outlet.

I need to build fence with automatic roller gate ASAP

The head of the dynabolt holding a gate hinge to wall has broken. The hinge is now loose. You’ll need to allow for : - removing the large gate including the motors swing arm - replacing the lower hinge (or just the bolt) - remounting the gate and making sure the gate swings correctly to work with the gate motor (no problem with the motors operating the gate previously). It may be possible to reuse the lower hinge, but it could be difficult digging out the old bolt and then securing a new bolt in that same place in a secure way. I’ll leave that up to you. Please explain how you intend to do the repair with your quote.

Looking for a qualified electrician to install an automatic gate control system. Power supply is already available at the gate. Please reach out with your availability and quotes.

We want to install a remote operated automatic gate at the front of our house. Ideally Bifold gate with motor attaached to the door so it doesn't take extra space. Or a sliding door. If it can curve into a back wall, would be best. If not, open on a hinge. Since its a small driveway, i would hope you can do this without taking too much space from the driveway. You would be expected to supply and install the gate. Build the side fence to accompany the gate for the entire entrance is blocked. Note: Electric connection not available so needs to be brought from the house (approx 20 ft).

Looking for someone experienced with automatic gates to diagnose and repair my remote-operated gate. Details: - Issue: Gate opens normally but won't close (could be faulty obstacle sensor or misalignment) - Type: Remote-operated sliding/automatic gate - Current setup: Photos attached showing: * Cream colored motor unit (shown in photo) * Black sensor box on white post has damage with temporary tape/glue repair * IMPORTANT: Cosmetic appearance of the repair isn't critical - main priority is getting the gate functioning safely and properly again - Timeframe: As soon as possible Requirements: - Experience with automatic gate systems - Must have own tools Please quote including: - Parts (if needed) - Labour - Call-out fee Please respond with: - Your experience with similar repairs - Earliest availability - Estimated cost range *Note: Please let me know if you need any additional information about the gate system.

The automatic gate closing mechanism on an entry gate to a block of flats does not push the door firmly enough closed so the latch clicks tight and engages with lock. The system is new but has never worked properly. Door never locks properly. Labour: $75. Travel time: $25 each way. Total budget: $125

i need someone to provide and install automatic front gates

I have an existing automatic gate system that has stopped working and I need to swap with similar new kit that has been purchase

DITEC entrematic automatic sliding gate not functioning properly. Sensors to be replaced. Old owner didn’t hand ever the key for the unit. Need new key to be done.

Fence around 40m. Automatic gate

Automatic gate x 2 - 15 m. Keys. I need the keys to work with my steelline - roller door. Front of house. Black/ gray in colour. Higher than 150m (?) Show me different designs you can put. Photos for measurements .

I’ve installed a new two door swing gate and need the closers reinstalled. Also need a new mounting bracket and one pin as shown.

Install New electrical Wire from the house to the External Automatic electric sliding gate. Job description is as fallows. - ELECTRICAL Connection already exists. POWER point is sitting in roof underneath the tiles. Also underneath the house. - You have run cable from house to the gate. - Connect the motor with wire. Material need to be supplied by the electrician. Motor will be installed by the another tradie who is installing the Automatic electrical sliding gate.

I need someone to fix my automatic gate. The previous installer was terrible.

We want to install a remote operated automatic gate at the front of our house. The door should be sliding door. If it can curve into a back wall, would be best. You would be expected to supply and install the gate. Note: Electric connection not available so needs to be brought from the house (approx 20 ft).

I have an automatic sliding gate with motor installed. I need someone with experience to install the track on the gate, hook up the motor with the provided power cable, install the gate stop , program the remote. All required materials are provided. Any questions please ask. The motor is Faac 740

I'm looking to install an automatic gate for the entrance to my backyard; right now, I have a manual one in place.

Need an experienced DiTec automatic gate specialist to troubleshoot a problem with automatic gates. System is an old DiTec E2 dual motor swing gate. Gates will not open or close properly. * Remote button pushed, gate initiates open procedure then stops after a few cms.

We need the front wooden gate cleaned thoroughly while ensuring the wood is protected and not damaged in the process. Please follow these guidelines: • Use a mild, wood-safe cleaner (avoid bleach or harsh chemicals that may strip the wood or affect any existing sealant). • If using a pressure washer, keep it on a low-pressure setting to avoid damaging the wood grain. • Focus on removing dirt, mildew, and discoloration, especially around joints and lower panels. • Rinse thoroughly and allow the gate to dry completely.

A small treated pine timber gate , less than 1 x metre by 1 x metre with galvanised hinges. Not more than 5mm gap surrounding the gate and the brick wall, and not less than 5mm between pine palings.

Want to add a timber gate to the top of our deck stairs. Simple is fine - something that will blend in with the deck. We can oil it later. Hoping for someone who can source the materials/hardware, build it to fit, and install it. The gap between the stair posts is 101cm wide, and from floor to top of the post is 102.5cm tall. Open to quotes! Please factor in materials into your quote. I've attached an image of our deck (no gate), and a sample photo of a gate that has the features we're looking for - simple, timber, with a latch.

Timber pane side gate requires sanding and repainting. Price quoted to include products required.

Can someone expertise help with supply and installation of a standard timber gate. You need to install two new posts, cut the existing fence and install a timber gate.

Require a timber gate to be replaced. Gate has already been purchased. Just need to put hinges on and replace

I have timber gates - pedestrian and automated driveway gates - that require tightening up and addressing of a small area of rot. There is also some small sections on the timber work of my house that need repair.

Hi we are looking to install new timber gates 2.2m wide 1.8m high with 2 swing doors. Something simple. After New concrete driveway is done. Thanks

Install a fence with a gate and 2 timber gates on 2 sides of a house

1 x gate requires timber panels to be re-fixed, deadlock to be supplied and installed and coated with a protective sealer 2 x gate requires timber panels to be re-fixed, and coated with a protective sealer

Weathered decking screen fence/gate. Needs oiling with a decking oil.

Front gate needs replacing. This is a solid unit with a mechanism which auto shuts. The price is for labour only. Materials paid for separately and on invoice.

Looking for a carpenter to help to replace a timber gate... 120cm (H) x 96cm (W) x 4.5cm (D). Two colors: windspray and tranquil retreat. Please include painting as well but we will provide paint.

Cut down timber gate to fit in between the frame and rehang.

Repair/ replace timber gate hinges and replace a few palings on adjoining fence. See photos.

Looking for a carpenter to rehang a timber gate (gate scrapping ground) + gaps emerging in gate so looking to "rebrace"/restore the gate.

We have two outdoor gates that need replacing. I would like them to be treated timber in a simple picket arch with a Z frame reinforcing the back. They will also need to be attached to the wall with hinges and latches. Gate sizes: Side garden gate 97 width // height approx 157cm https://www.bunnings.com.au/900-x-1800mm-gate-cypress-arch_p0124921 Pool gate Width 83cm // height approx 140cm There are prefab ones at Bunnings for $148 that will suit the larger size, but not the smaller. The smaller will have to be built or perhaps we can cut another Bunnings one to size. Will need you to purchase materials after we discuss design, build gates and install.

Build and hang new timber gate, including hardware to replace rotten timber gate. Paint semi-gloss white. Clean, remove mildew and paint the remaining 15m of the fence - paint semi-gloss white.

Updated task (changed from below) Take off gate, repair bottom edge where broken/rotted, repaint and rehang with hardware (new provided if needed) a bit higher so doesn’t drag ground (is there something we can put on bottom edge like a little castor to keep it from reaching ground) ————————— Original post 1. Refurbish / repurpose this gate. Remove and use parts plus new wood pieces to make a single (but wide) smaller gate and 2 side panels (like example in photo). The gate has some rot at the bottom due to dragging the ground and rain (see photo). 2. Strip/sand/repaint in Woodland Grey (Dulux colour) exterior paint. This would involve removing the hardware. New hardware will be sourced for rehanging. You can do this job onsite here or take gates away if you prefer to do at your workshop. See photo of what I want the end result to be similar to (but not colour). We have a fencer coming in a couple weeks who can then install new posts and hang it. I have just put an amount in here to post, please quote as you see fit.

We have 1m wide gate that is very sticky and requires more effort to open and close than it should.