Find a professional gate installation in Central Coast

Install a garden gate to the backyard

Terrigal Install a baby gate at the top of the stairs. Drilling into brick, see photos attached. Just ordered the gate and will arrive early next week so would like doing next week please. See pictures attached.

Emergency repair to exterior balcony. Reattach gate post to concrete wall. All material and fixtures supplied. Property location: Toowoon Bay

A gate latch is damaged and needs a replacement. Also the rain down pipe in the backyard has a hole needed to be fixed.

Hello, Need help putting steel side gate on. Thank you!

I have 3 x new security gates to be installed

Hi, I’m looking for someone experienced in fencing installation to install a garden fence at my property around Killcare on the Central Coast. The purpose is to create a secure area for our dog and chickens. I have already purchased the main materials, so I’m mainly looking for labour and installation. Fence: • Approximately 30m of fencing • 1.2m high Jack Pro Series Heavy Duty Dog Mesh, already purchased • 15 × 1.7m steel fence posts, already purchased • Posts approximately 2m apart, adjusted as needed • Posts to be driven approximately 50–60cm into the ground • Mesh securely attached to the posts with galvanised tie wire • Bottom of mesh needs to be secured well to prevent the dog digging underneath. (haven't bought anything yet, but looking for recommendation on the day) Important: the land is NOT flat. The garden is uneven and slopes in places, so the fence will need to follow the existing contours of the land rather than being perfectly level. Experience with mesh fencing on uneven/sloping ground is preferred. Gate: • One access gate, approximately 80–90cm wide and 1.2m high • Gate with its own two posts • Secure latch so the dog cannot open it • Happy to use a suitable ready made gate or framed mesh gate Materials already purchased: mesh, 15 steel posts and galvanised tie wire. I can purchase any additional brackets, anchors or gate hardware required. Please quote labour only, ideally with a site visit before confirming the price. I can provide photos of the area.

Hey there, is someone free this weekend to come fix some holes in some gyprock from a baby gate please

Metal gate needs hinges welded on

Want to install a sliding gate and a swing gate next to it for the front of a house/driveway

Hinges have snapped off our back gate on our deck. Heavy duty hinges that were welded to the gate frame

1 Baby gate (perma) to install for staircase - all parts are together.

Alcano sliding gate motor in Wyong. Everything has already been installed and set up, including the electrical cable to the gate. We just need a licensed electrician to make the final electrical connection, check the connection and make sure the gate motor is operating correctly. Also need the supplied remote controls programmed/paired and the gate fully tested for opening and closing before completion. We have the manufacturer's manual available.

I have bougt an extendable steel gate to close off under my deck. I need gate hung and then pine boards attached to the front to match the deck

(1) Supply galvanised door hinges & replace those existing on two gates. (2) Make & fit 2 x post skirts 370 x 160mm & 270 x 160mm approx including prep for painting. (3) Replace internal damaged door casing. (4) Cut top off Kopper Log. All materials to be provided by contractor and carpentry skills required for all tasks.

The lock and handle on my front gate door is difficult for people to open due to it being loose and broken i would like someone to help me out with replacing it. I do not know what kind of lock it needs and was wondering could someone get a knew lock handle for me and come out and replace the old one.

We need someone to fix the gate and secure it. Check photo attached please.

Timber Pickett fence Left side neighbours fence to left edge of drive way 7.3m Left side driveway to right side drive way 5m Right side driveway to right side neighbours 2.5m Roughly 10m of Pickett fence and 5m Pickett gate We want 1.8m length pickets The photo is a rough idea of what I’d like we will do the painting We want the key details like the black hinges and for the fence to look as close to that one in the photo

I need a small timber gate painted nicely. It will need to be painted with a primer then a few top coats It’s been lightly sanded. It needs some screw holes or gaps filled and it needs more sanding. I will provide paint, sandpaper, brushes, rollers

My gate has broken off the hinges from the wind and needs putting back