Find a professional gate installation in Perth

Manual roller door has come off rail. Needs to be re set and cleaned around the insert.

We are a pilates studio in Floreat needing a fence to be installed for our kids zone. We will purchase the raw materials from Perth Fencing Supplies and need assistance installing it in the space.

Repair garden gate hinge. I don’t have the tool to do it nor the bolts as they look like rivets. Just looking for handyman to come and install new on both hinges to secure in places. Make offer

Two pool gates don’t fully latch from up close. Need to tighten and adjust pool gate hinges or latches to pass council inspection.

Paint fence gate and arbour. Filler needs sanding back and 2-3 coats of paint. I have paint on site.

Two pool gates don’t fully latch from up close. Need to tighten and adjust pool gate hinges or latches to pass council inspection.

Supply and install a post, gate and hardware for a white (scalloped) timber picket fence Gate: 1160mm x 940mm wide Post 1200mm above ground level Including supply of paint and painting

Install new CISA 12V Electric Rim Lock 11721-60-2 gate lock. Electric is connected fine but the existing lock is faulty. I have ordered the new lock just needs to be installed.

Blockage between gully at rear and main sewer (roots?) Old house and likely earthenware drains.

Limestone pavers at entry pedestrian gate need relaid and cemented in 1m x 1m

Installation of garden gate & small fence (total width combined 2.35m) on one side of the house. Photo attached of area, currently a temporary freestanding baby gate is in the position. Fence & gate to be ordered through Bunnings (eg Protectoral brand).

Install New Pedestrian Gate Looking for an experienced handyman or fencing contractor to supply and install a new pedestrian gate between two existing limestone walls. Gap between the limestone walls is approx 940mm. Open to offers. Scope of works: - Install a new white pedestrian gate, preference is aluminium horizontal slats - Install a new white hinge post and hardware. - Install self-closing hinges and latch. - approx 1.5m tall - to go across bottom of stairs on first step Please include in your quote: - Labour. - Whether you can supply the gate and materials, approx cost. Photos of the existing opening and and example gate are attached.

Need a gate and it to be installed in my portico that opens into the front yard. Photos are AI generated as to what it might look like. The AI generated shot has the gate on the outside of the portico where it needs to inside the portico,

The task is to weld the lock plate onto the gate as shown in the photo. Both are galvanised steel. There is alignment marks for positioning.

Hi, I just need a baby gate installed - drilled into the wall. If possible, this afternoon between 3 and 4pm? We live in Nedlands.

I’m looking for a licensed electrician to extend an existing electrical line/power supply to a point near my front gate. Job details: * Extend/run an electrical line from the existing connection to near the gate * Properly secure and install the cable according to Australian electrical standards * Assess the existing setup and advise on the best solution * Materials can be discussed with the electrician

Looking for a carpenter or experienced handyman to repair an old timber side gate at a Subiaco property. It is a heavy ledged and braced gate, arched top, hung on a timber post fixed to a limestone wall. The gate swings inward. ISSUES: 1. The gate has dropped and now rubs on the closing side so it does not shut properly. The existing pin-and-strap hinges are worn and rusting. Both hinges need replacing and the gate rehung square. 2. The ring handle has come off and the latch no longer works. The timber around the old handle is split and the screw holes are chewed out, so it needs making good before new hardware is fitted. 3. There is a split with some rot at the top of the closing stile that needs cutting back, filling or splicing, and repainting. SCOPE: - Replace both hinges with heavy duty galvanised or stainless through-bolted hinges and rehang the gate square so it closes and latches cleanly - Repair the timber around the handle and at the top of the closing stile - Supply and fit a new two-part gate latch (D&D LokkLatch Deluxe S3 or equivalent) that operates and locks from both sides. Pack out the latch post with a hardwood mounting block if the existing face is too narrow. - Refit the existing cast ring handle as a pull, repairing the split timber behind it - Plane the closing edge only if genuinely required after rehanging, and seal any cut edge NOTES: - Please diagnose and correct the drop first. I do not want the gate simply planed to clear the rub. - Hardware will be supplied, or quote for it separately. - Please bring your own tools, and a small offcut of hardwood in case the latch post needs packing out. - Must be comfortable working with older timber and fixing into limestone or render if the post needs attention. - Happy to send photos of the hinges, handle and closing stile.

I have a new smart lock that will replace this one. You will need to supply and replace the current metal plate as the holes currently don’t line up. Please bring all tools for the job.

I have 2 glass gates attached to my pool fences which are sticky and slow to close. I need them fixed ahead of the pool inspection