Find professional metal gate repairs in NSW

We have a beautiful metal gate with some wooden inserts. The bottom of the gate is rusted and needs to be repaired and some of the internal "struts". The bottom of the gate is the worst affected. Please see images....

The metal gate is out of alignment and needs to be fixed

Need a metal gate repaired. Will require on site welding.

Looking for someone to repair our metal front gate. One of the welded joints has come apart and the metal section has detached. Would like it reattached securely and restored to its original position. Please see photos. Ideally looking for someone experienced with metal gate repairs/welding.

I have garden metal gate that is attached with 2 screws need removed

Need to reattach metal (iron) gate to wooden post, and provide a latch for the other side. Gate is 2x1m. The gate came off in the wind.

I have a metal gate which has rusted at the bottom. I’d like the rusty bottom bar cut out and a new piece welded in. The gate has a curve to it as well.

Looking for a handyman to refit a small decorative metal gate( red gate as in pic)that’s come loose from its groove. The gate needs to be reattached securely to the brick wall ideally using a bracket or clamp setup similar to the example shown in the green gate photo.Expecting the handyman to - Inspect current gate alignment and mounting points. Supply and install suitable brackets or clamps.Ensure gate is level, secure and functional

A top handing metal gate is off the rail, need to get a part to slide it back to the rail

Gate needs to be level & lockable. You will need to supply necessary brackets to mount gate. It may require a second post to position gate in connect location.

Hi, I need a handyman to supply and install a dual-sided gate latch (like a D&D LokkLatch Deluxe) on an existing metal side gate and metal post at my home on Mary Jane Parade.The latch needs to open from the outside and have the option to be locked from the inside.I am currently away from the gate but will upload clear photos of the metal frame, post, and gap tomorrow morning so you can see the setup.Please provide an estimated quote for labor + supplying the lock hardware. Thank you!

My outdoor metal gate has become slightly misaligned, so the deadbolt no longer lines up properly with the receiver and is difficult/impossible to lock. I’m looking for someone experienced with gates or locksmith work to inspect and fix the issue. It may involve adjusting the gate hinges, realigning the lock/strike plate, or another suitable repair so the gate locks smoothly again. Please include any small parts/materials required in your quote. The quote should include call-out fee, labour and minor parts. If you believe a major part replacement is required that would exceed this budget, please discuss it with me before proceeding. I’ve attached a photo of the current lock for reference.

The current G8SAFE top-pull latch is installed at 147cm because the existing post is too short. Please extend the height of the post using a matching black square tube extension/sleeve so that the existing G8SAFE latch can be reinstalled with the top handle at a compliant height of 170cm or higher. Please note: Simply reinstalling or shifting the latch higher without extending the post is NOT acceptable, as the latch body must be fully supported by the post. Please bring necessary tools, black metal extension pieces (approx. 50x50mm), and black touch-up paint. Thanks!

My metal gate has stopped closing due to erosion/wear on the latch area. The latch no longer lines up or catches properly, and the gate can’t be secured. I need someone who can assess the damage, realign or rebuild the latch mechanism, and ensure the gate closes smoothly and safely again.

70mm long metal hinge on gate rusted off. Request new hinge welded on or this one repaired if possible

The current G8SAFE top-pull latch is installed at 147 cm because the existing post is too short. Please extend the height of the post using a matching black square tube extension/sleeve so that the existing G8SAFE latch can be reinstalled at a compliant height of 160 cm or higher. Simply reinstalling the latch without extending the post is not acceptable.

I need someone to repair or replace the latch on my side timber fence gate. The metal latch has become bent/damaged and no longer closes properly. I’m happy for it to be repaired if possible, or replaced with a similar galvanised latch if necessary. Scope of work: * Inspect the existing gate latch * Repair or replace the damaged latch * Ensure the gate opens, closes and locks securely * Please supply a suitable replacement latch if required (or let me know the additional cost) Location: Kellyville NSW Please quote including labour. If replacement parts are needed, please specify whether they are included or charged separately. I’ve attached photos of the existing latch.

The D-latch handle on my metal gate is broken and needs to be replaced. Please supply and install a compatible replacement D-latch handle (black colour) and ensure the gate operates correctly. Photos are attached.

I have a metal front gate. The hinge has rusted out/failed. I purchased additional hinges from Bunnings, but I don’t think the holes accurately line up for the screws. Will need someone that is able to fix/reattach. Photo is what it looks like properly attached.

To supply and install electrical lock for metal gate