Find experienced local carpenters in St Kilda East

2040 x 620 door needs to be trimmed so that it is 2040 x 600. Wooden door

Hey, looking for someone to help convert an enclosed outdoor area into a shed that we can actually use. Please see pics for an idea... Approx area is 2.5m x 1.3m x 2.3m. We don't have materials. Thanks in advance

Need carpenter to help with skirting boards. Boards need to be cut and installed in 4 rooms in our house either today or tomorrow (Saturday 23/3). We’ve already bought the skirting boards new and they are ready to be installed once cut.

Supply and install timber floating floor to two areas to match existing. Floor boards 185x14mm Tas Oak (I think, or similar) Area 01 - rectangular area (image with furniture on it over yellow tongue board) 3200mm X 650/835mm (depending if existing board is retained)X 3200mm) Area 02 - Stair landing (image of irregular shape, white painted board with mat on it) 2300 X 1050mm (max dimensions), plus one stair nosing to finish

Pee stain resulted by pet, we have tried cleaning with cleaning solution with no effect. Help please

Built in bookshelves A) approx 3400 x 1500 x 340mm b) corner bookshelf approx 2500 x 500 / 850 x 250mm spotted gum in style as shown

Design and build shelving that look good, sleek and functional. They need to be built in to carry books. Design should be book 4-5 book shelves that is above the bed and options for design on the sides of the bed. The back wall and one side wall is brick. - Due date: Flexible

Assembly and installation of Mimosa 3.66 x 2.95m Lava Brighton Louvre Panel Gazebo (Bunnings) to small paved backyard (5 x 6 m plus another metre of surrounding garden bed). Pavers may be slightly out of level at gazebo leg points but easily addressed. Does not require fixing to ground / pavers.

Need our deck sanded back and stained, approx 6 x 4meters.

The bottom part of the exterior of my window frame (in the balcony) has water damage. I need a handyman with some timber experience to rebuild it or just cover/protect it. - Due date: Flexible

Stain timber deck Roughly 20sqm 2 Steps - Due date: Before Tuesday, 9 January 2024

custom made and installed wardrobe in bedroom - Due date: Flexible

I am looking for someone to install small ikea galley kitchen. The old kitchen has been demolished. The electrician and plumber have completed first fix. Six cabinets in total. The benches are being done separately and not part of this job. All cabinets are metod. The cabinets are: 2 x base 40cm 3 draws 1x base 80cm 2 doors for sink 1x base 20cm with pullout 1x base for microwave 1 x wall cabinet for rangehood The sink cabinet will require cut out for plumbing & power point. The microwave & range hood cabinets will require cut out for power point. Floor tiling is being installed next 2 days so ideally cabinets are installed between 15 - 24/12 or after 8 Jan. I have included pics of room & design. - Due date: Flexible

Seeking a craftsman who can construct a vinyl record holder tower from copper pipe with a wooden top, as shown in the attached images. Specifications as follows: External frame material: 22mm copper Internal vinyl rail material: 15mm copper All joints to be professionally soldered with minimal solder residue externally visible at the joint. Finish to be polished for a bright and shiny effect that shows off the copper. Lacquer to be applied to seal the copper against oxidisation to maintain its shine. Removable Tabletop: Walnut or Oak Wood, stained and finished to a high standard (also open to alternate suggestions for type of wood). Professionally joined to pipework as shown in image. Top edges routed to create a soft curved edge. Height x Width x Depth: 980 x 410 x 310 mm - Due date: Flexible

We have a steel garden bed which is seeming to be very difficult to remove. It’s solid steel and double bolted in. Would need to cut or melt most likely, we just don’t have correct machinery. - Due date: Flexible

We need assistance in finishing putting up a garden shed. The sides and roof panels have already been put together. 2.25m x 0.78m Flat Roof Shed Assistance is needed for: -Door Assembly: Fitting hinges, Attaching door plate & padbolt, Fitting door braces -Fasten wall panels and roof together -Secure the shed into the concrete floor (we have the set of concrete anchor fixings ready to be drilled) -Equipment required: Step Ladder, Pop Rivet Gun and Hammer Drill with Masonry Drill Bit My partner will be there to do this with you. He just needs the extra pair of hands. We’re looking for someone with a bit of expertise who also has the equipment needed. It needs to be done this weekend on Saturday 4th Nov. - Due date: Needs to be done on Saturday, 4 November 2023

I have 8 short lengths of treated pine, each of which need an identical cut out from the base (as pictured) - Due date: Flexible

Build ramp between rooms. Have surplus flooring to use. - Due date: Flexible

Looking for a handy man or carpenter to make us a custom timber shed on our deck. Approximate size 3m wide x 1.5m deep. Roof approx 2m high. 1 x window. Hinged door. - Due date: Flexible

We have the majority of our Kaboodle kitchen cabinets installed however our installer has gone on holidays. All we have left to install at this stage is the microwave cabinet attached to the wall and adjoining fridge space. A wall cabinet above the microwave cabinet. And an L shape benchtop attached as it is sitting on top of the installed cabinet bases.