Find experienced local carpenters in Melbourne

Timber window is stuck and won’t open or close.

Hello, We need help putting a hinge on a cabinet door for our kitchen. We have the Hinge Pack but looking for someone to install it. Please see the photo's below for more in detail.

I need help replacing an existing integrated compact dishwasher (Smeg ST201XA) with a new unit (HV-D6FI). This is not a straight swap — the new unit has a different door/hinge setup. Photos attached show: Current Smeg installation Existing panel alignment Internal hinge/rail setup Cabinet opening ⚠️ The Challenge The existing Smeg uses a sliding-style hinge system, which allows the cabinet panel to move as the door opens. The new unit (HV-D6FI) appears to use a more standard fixed hinge setup. Because of this: The panel alignment may not match The mounting points will likely need to be redone The door swing may need adjusting to avoid hitting the cabinet base Current panel layout: Door section ~410 mm Bottom panel ~67 mm New unit appears closer to: Door section ~330 mm Larger fixed bottom section So the split between door and base shifts, which affects alignment. ✅ What I need done Remove existing dishwasher Install new unit (HV-D6FI) Modify / reposition cabinet panel to suit new hinge geometry Ensure: Clean alignment with surrounding cabinetry Smooth door opening (no rubbing/hitting) Solid mounting 🧰 Looking for someone who: Has experience with integrated dishwashers (not just freestanding installs) Understands cabinet panel fitting + hinge systems Can problem solve alignment differences Can make it look neat and intentional

I am looking for a joiner or cabiner maker. Specifically 1. retro fit 2 x drawer units inot an island bench each (1000 mm w x 680 mk high x 580 mm d) each with 3 drawers 2. retrofit 6 drawer units into a pantry each (470 mm w x 480 mm d) 3. Build 1 x cupboard with a top-hinged door (no shelves) to sit above a fridge (960mm w x 500mm h x 600d) 4. Repair (or replace (can use the existing front panel on one drawer unit) 5. Supply and install sliding doors (including tracks) to a wardrobe Drawer Units are located in Prahran, Sliding doors for the wardrobe in located in Hawthorn East - all finishes in melamine except wardrobe doors, which will need to be in chipboard so they can be painted to match the existing wardrobe unit.

Remove, sand and stain wooden in-built seating and back courtyard fence and re-attach. Seating and fence is in-built and has a dark stain on the solid timber. Would like it sanded and a much lighter shade of stain. Happy to pay for stain and sanding pads separately to time, upon receipt.

Looking for an experienced carpenter to trim/ custom fit an IKEA bathroom cabinet into an existing cabinet. Job details: • Cabinet size approx: 100 cm height × 70 cm width • Require trimming, adjustments for a proper fit • Ensure cabinet is level, securely fixed, and neatly finished • Wall-existing cabinet, mounted installation Location: Port Melbourne Requirements: • Proven experience with custom cabinets, cabinet installation / carpentry • Own tools and equipment • Attention to detail for a clean, flush finish • Ability to advise on best fitting solution if adjustments are needed • Ability to source or recommend trims etc Timing: Flexible — ideally within the next 1–2 weeks. Welcome to have a meeting on site to quote the job.

The rivets on a strut of my 1970s bathroom window have come loose and need replacing. Unit is on second floor of apartment block. Window is wooden bathroom c. 1500mm x 600mm, above bath and c.1700mm sill height.

I have lockers that need to be raised a few cm so the bottem row of cupboards can open freely, they currently scrape on ground which destroys the hinges. Also fixing the hinges once complete.

I have a round wooden table top. It is not attached to a base. I need someone to make two STRAIGHT cuts (where I marked with blue) to make the table narrower. You can set up in the carport of my apartment building (there is a power point you can plug into) I'm assuming you will need a saw table and/or guide rail. Thanks

Timber panel/cladding under window is cracked and breaking. There appears to be a gap under the window frame that may lead into the floor cavity Located on second story so ladder required. Need someone to inspect, repair/replace timber and seal the gap to weatherproof. Prefer carpenter or experienced handyman Please include materials if needed

Hello, I’m in need of a handyman with a drill to carry out a small job – specifically, making a larger hole in a cupboard and drilling through a piece of wood. The work can be done this evening or tomorrow evening at your convenience. No additional work is required beyond the drilling itself.

I need a cable hole drilled in 2 ikea rudsta metal cabinet to turn them into greenhouses. I will need a cable hole cover for each of the cabinets as well. This is what I'm doing for reference (10:35 she drills the hole) https://youtu.be/gdWqxjSRkCk?si=wNEuoDCEXCrponjr

Fix two external doors not lining up or latching. Remove rotten skirting board and door jambs and replace with new moisture resistant timber that I will supply.

My cabinet door has fallen off the hinges and needs to be hung back up. There are now large holes where the hinges used to be so these may need to be refilled and new screws drilled?

Need a wooden box built to cover irrigation system

See photos. Have a timber door which needs repair.

Need a carpenter or handyman to fix this broken step on our back staircase of our bar

Supply and build/attach custom shelves to existing cupboard I’ve outlined where I want the 3 extra shelves Color matching of shelf not necessary/optional

Our IKEA integrated dishwasher is not opening / closing properly - we need someone to go check out what the issue is and either resolve it with new hinges / etc. or installing a new cabinet front to the dishwasher with proper hinges/rails. I believe it wasn't installed right in the first place, and was GLUED onto the dishwasher instead of on the conecting rails. So some kind of glue removal might be required to save us from replacing the whole dishwasher. OR remove the (damaged?) IKEA cabinet door and PICK UP another one from IKEA in richmond / springvale. I can give you the exact products we purchased with the original kitchen. I basically need someone to work out what the problem is, and solve it haha. Let me know if you're my guy/gal! Available Saturday for urgent attn.