Find an experienced handyman in Canterbury VIC

Our kitchen was installed around 2010 and four of the soft close drawers no longer 'catch' and stay shut. They are all 'press to open'. The company which installed the kitchen is out of business and I can't find replacements of the fittings at the rear of the cabinets which seem to keep the drawers closed. New slide mechanisms with a similar soft close and push to open may be required. We are willing to buy replacement parts or have you supply them.

Replace 6 door locks/knobs

I would like to make this side fence more soundproof to eliminate traffic noise. Not sure if metal or wood backing to each part of the fence but am open to ideas. Would also consider a vinyl wrap or something similar if it will help with noise. The gate still needs to open and close normally so I think 3 separate backings will be needed. And it needs to look aesthetically pleasing!

Install a PVC bistro blind at the end of the deck. Instructions are online - see 'How To Install Bistro Blinds - DIY At Bunnings' My husband can help hold the other end - it's very light.

* external woodworking rotten and needs repairing * painted after repair

Hello - we need a handyman to help remove/detach a ceiling mounted projector in Canterbury. We have two guys here already to remove the projector but it'd be good to have someone handy with an extra pair of hands to help. It's a heavy projector. Sometime this afternoon around 2pm

Hi there, I’m looking for a reliable and experienced person to install some timber wall panels in an interior room. There are 7 panels to be installed - I’d like panels to be screwed (using black screws) into studs rather than using glue. Wall is 400 (w) x 300cm (h). Each panel is 60 (w) x 280cm (h) so there’s no need to cut panels for height, but you’ll need to make some cuts in panels to allow for a couple of in-wall speakers and GPOs (see photos). I’d also like an IKEA floating shelf (110cm) installed over the timber panels once installed. Wednesday 9 April or Friday 11 April works best for me. Thanks Lawrence.

Fix my front porch where a two vertical and horizontal wooden slats have come loose.

Blind cord snapped off, blind came down

Install a floating shelf on a plaster wall

We have a half-built Stratco Umbra Awning shed needing completion - the frame is up, but we need the sides and door fitted

Single cane chair, relatively new, has damage to seat only. Likely needs seat only replaced.

I'm replacing an existing door. New door needs 10mm trimmed off top and 15mm trimmed off one side. Hang door using existing hinges and install existing lock into new door.

Need the bottom of thus frame pushed/glued back together, see pictures attached and dimensions below Handfinished 79 x 59.7 cm / Gallery Profile 13 x 35mm Vic Ash - Black Lacquer Open Grain

We have a rental above a commercial property with two split systems - one is ok but the other isnt blowing cool air… no rush would like them both serviced

A roller blind that is approx 251cm long has had its base rail detach. Need a trade to replace the spline onto the blind and then reattach the base rail.

Looking for 3 coats of paint. I will supply paint. Paint is dulux - whisper white. small job. Painter must be have experience and insurance Awning is small - ground level, although small ladder, or steps will be required. Awning length is approx 1.6m

1.9m heigh x 1.58m width mirror/each. Need 2 pieces to be installed onto the plaster wall。The width of the entire wallis 3.33m. Require frameless, with polished edge. The room is easy access from garage… No staircase.

Hi there I’m looking for a reliable and experienced person to install two IKEA floating shelves (each 190cm x 26cm x 5cm). The shelves will need to be installed onto plasterboard and into the studs. You’ll need to supply your own tools / equipment. Thanks Lawrence.

Was soo confident i cld do this myself but finding studs is apparently beyond me… I need help installing three small shelves of the Besta system. The shelves are assembled, i have all brackets for wall installation but lack a decent stud finder and some knowhow and muscle to hang it.