Find an experienced gas fitter in NSW

Replace the gas jets and igniters

Seeking gasfitter/plumber to relocate our existing LPG gas bottles and Bosch gas hot water system to an adjacent position along the exterior wall of our house. Please refer to the attached photos showing the current installation and surrounding area. Scope of work: 1. Relocate LPG gas bottles * Safely disconnect and relocate the existing two LPG gas bottles. * Move them to the adjacent designated space along the exterior wall. * Reconnect and check all gas fittings, regulators and connections. 2. Relocate Bosch hot water system * Disconnect and relocate the existing Bosch gas hot water unit to the new position. * Extend or modify existing gas, water and hot water pipework as required. * Ensure correct ventilation, clearances and compliant installation. * Test the system to ensure it is operating properly after relocation. 3. Relocate concrete base * Move the existing concrete slab/plinth currently supporting the gas bottles to the new position, if suitable. * Ensure the base is level, stable and appropriate for the relocated equipment. * Advise if a new concrete base is required. Requirements: * Must hold the appropriate NSW licences and qualifications for gasfitting and plumbing work. * Must have experience relocating LPG installations and gas instantaneous hot water systems. * All work must comply with relevant Australian standards and NSW regulations. * Please include testing for gas leaks and confirmation that the hot water system is functioning correctly. Quoting: Please provide a quote covering labour, materials, pipework modifications and any additional requirements. I have attached photos of the existing installation and the adjacent space where I would like the equipment relocated. Ideally, I would like all work completed in one visit. Thank you!

Need someone to disconnect our gas bbq that is a built in Beefeater 6 burner pro-line and move it into the garage. Approx 15m walk with stairs. 8-9am

We have a small block of 6 one bedroom apartments and have very recently had all the gas meters replaced. We need for our Fire Compliance to have a licenced gas plumber check the gas and provide us with a certification as complying with the relevant safety requirements of Australian Standard 5601.1-2010. There are NO issues, no leaks - just for compliance certificate only.

Hi, I need a Licensed Gasfitter to inspect and repair an LPG gas leak at my house. Job Details: Location/Type: Outdoor wall-mounted dual LPG cylinder setup. Issue: Soapy water test confirmed a gas leak at the joint between the brass manual changeover valve and the Cavagna LPG regulator. Current Status: The LPG cylinder valves are currently turned off for safety. Requirements: Inspect, reseal, or replace the fitting/regulator connection as required. Perform a standard leak/pressure test after repair. Budget covers labour and the pressure test. If parts (such as the regulator or brass fittings) need to be replaced after your on-site inspection, the cost of parts will be paid separately at actual cost. Must be a licensed NSW gasfitter. Please provide your gasfitting licence number when making an offer. Thanks!

I have a Ziegler & Brown Twin Grill (sold by Barbeques Galore, which is no longer trading) looking to convert it from natural gas to LPG. I can bring it to anywhere in Sydney BBQ details (from the rating label): • Model: ZGTGNGE (Natural Gas). The LPG equivalent is ZGTGE (Universal LPG) • Serial: ZGTGNGER2023090133 • Date of manufacture: September 2023 • IAPMO/GasMark number: GMK 10827 • Current NG setup: 1.52 mm burner injectors, 1.0 kPa burner pressure • Target LPG setup: 0.92 mm burner injectors, 2.75 kPa burner pressure • Gas use: 11.6 MJ/h per burner, 23.2 MJ/h total (two burners) The manual specifies an LCC27 safety hose and regulator for LPG, with a 3/8" SAE (5/8" UNF) right-hand thread at the barbeque connection. It will be used with a swap n go LCC27 cylinder.

Looking for a licensed gasfitter to lower the gas connection behind our freestanding oven so it can sit flush against the wall. The rigid copper line comes up through the floorboards to an ARCO ball valve and a braided flexible hose. The valve and fittings sit too high, so the oven sits out from the wall, which isn’t safe. Scope (all materials included): -Isolate gas and cut back or lower the copper supply line -Relocate, replace or recess the isolation valve so the oven sits flush -Reconnect with a compliant flexible hose of the correct length -Check existing fittings (some green corrosion on the copper joint near the valve) -Fit an anti-tilt bracket or chain if one isn’t installed -Leak test, recommission the oven and provide a Certificate of Compliance Access: metered street parking only. In your offer, please include: -Your gasfitting licence number -A fixed price, including all materials -Confirmation that you can complete the work this Friday between 10am and 2pm

There is currently an active gas leak on a yellow gas pipe joint located in the ceiling cavity. To make the repair straightforward, the ceiling drywall is already cut open, providing clear, direct physical access to the compromised joint. A soap test has been performed, confirming continuous bubbling at the joint where a green epoxy sealant was previously applied.

We have moved into a place that has natural gas, and it has a port outside to plug in a bbq. However it is not working with the BBQ we have. I suspect the valve has deteriorated and is not releasing properly. We need someone to inspect, repair and if necessary replace the outlet.

BBQ Galore turbo classic ziegler and brown bbq is lighting to the gas mains - maybe just not connected properly as it will light manually

I have purchased a new gas hob to do a straight swap out of my old one. Power Points and gas position in compliance (9 yr old building). Apartment so will need gas seal test.

Need copper gas pipe going to fridge crimped shut as changing out the 3 way fridge

There is a gas connection within a bed room that needs to be closed off from the outside.

I have just replaced my gas stovetop with an induction one and need someone to help cap the unused gas line.

Need gas point installed for Gas bbq

Need to connect gas oven. Also check why washing machine isn't getting water flow in.

I want to remove 1 gas bayonet point as it's in the way of my new skirting board.

I have a gas leak coming from my kitchen cooktop and need a licensed plumber/gas fitter to inspect it, identify the source of the leak, and repair it.

LICENSED Gas plumber needed to 1. remove gas cooktop / block gas pipe but leave gas meter. Cap off. 2. remove / block gas heater bayonet from wall behind sofa. Cap off Apartment in surry hills 2010, car park access, elevator. Gas meter etc is under kitchen sink opposite to cooktop Gas cooktop connection is next to oven Would like this done Tuesday 25 Aug or Wed 26 Aug - time flexibe

Need to cap off a gas cooktop as I’m installing new induction cooktop.