Find experienced local fencing contractors in Edithvale

Replace current latch on metal fence. Need metal drill bits.

Pool Fence Installation – Labour Only – Edithvale Looking for an experienced fencer, carpenter or skilled handyman to install our new timber pool fence in Edithvale. We supply all fencing materials. We are seeking a fixed quote for the complete installation/labour, not an hourly rate. Fence details: * Approx. 27.8m total pool fencing * 13 × 2000mm W × 1200mm H panels * Panels: 40 × 30mm Spotted Gum vertical battens, approx. 77mm spacing, with tubing through battens for rigidity * 2 × 918mm W × 1200mm H gates * 2 × pool gate lock/latch kits * Approx. 18 × Cypress posts – 90 × 90 × 1800mm Scope: Set out fence according to supplied plans, dig post holes, install/level and concrete Cypress posts, fix all panels to posts, install both gates and latch hardware, and ensure everything is straight, secure and operating correctly. The fence is going into garden beds/ground, not an existing concrete slab. Landscaping has not yet been completed, so access is easy, with predominantly sandy soil, making post-hole digging relatively straightforward. We already have the fencing and posts. Once we meet and confirm the amount required, we are happy to purchase and have the concrete/post mix on site. Please see attached images showing the panel design and the recommended method for fixing the panels to the Cypress posts. As this is a pool safety barrier, installation must meet the manufacturer’s requirements and applicable Victorian pool-fencing requirements. Trades must have current public liability insurance, relevant fencing experience and their own tools/equipment. Please quote for the FULL scope of works, including installation of all posts, panels, gates and hardware. Please also include examples/photos of similar work if available.

Both my fences either side of my property are leaning. Looks to be about 9 posts in total that need fixing.

I need a colourbond driveway gate. Total opening is 4880mm, with a swing gate of 3400mm, the remainder being fenced. The height 1800mm. Also a side gate width 1250mm, height 1600mm. I might also want the garden fence about 20 metres done. So, I prefer an onsite quote.

Replace metal edging and render brick fence ready for painting

We need a professional gate installer to build and install a custom metal gate frame with track and motor. Current opening is 2.8m wide and finished fence height will be 2m. Hampton style fence. We will do our own cladding after gate is installed. We also also provide the electrical connection section for motor.

We have 2 broken glass panels, 3m by 1.2 m that need to be replaced on our spa pool fence

We are redesigning the way we have our pool fence to open up our yard. We want to remove the 3 panels on the deck and place them along the pool up to the two pillars. We will need a couple of custom built panels and 1 door. Not sure if it’s an airtasker job or not but hopefully someone can help within a budget

We have 3 glass fence panels we will need removed and then re-installed as well as a few others installed and fitted accordingly. There will be one door installed inbetween the two pillars in the picture. We will obviously purchase the extra glass panels once they are measured up by who ever can install. Money is for labour to install.

Remove old timber fence and install new 2.0M high timber fence. New posts to be concreted in at 1.5M, install new plynth or retainer along bottom of fence. Fence is 28.5M in length.

An Australia Post motorbike clipped my fence, damaging 8 pickets. The task is to supply 8 cypress pine 100cm Windsor pickets, cut to length, 3 coats of paint. Remove broken pickets. Affix new pickets to fence, fill nail holes, final coat of paint and dispose of waste. Australia Post will cover the costs.

Existing timber fence to be removed and replaced. Approximately 6.7m long and palings to be higher than current height.

Looking for a skilled professional to install a driveway electric gate. The gate should provide full coverage and blend well with the existing fence. Details: Type of Gate: Electric sliding or swing gate (depending on your recommendation for the space). Fence Condition: Old but stable, the property will be demolished in 5-6 years. Driveway Dimensions: TBA - see photos. Material Preference: Affordable yet durable material that can last 5-6 years. Power Supply: Electricity available nearby for motor installation. Extras: Include intercom/keypad installation if possible. Requirements: Experienced in installing electric gates and motors. Must bring all tools and materials (I can purchase gate/materials if advised in advance). Please provide a quote and estimated timeline for the job. I’m happy to discuss details and negotiate if needed. Looking forward to hearing from you!

Need someone to fix tension wire fence at the front of house. Tension screw has been pulled out of post after a branch fell on it. Needs rescrewing with tension.

15m treated pine paling fence. 3m + 12 m with a 3m space in the middle. In the 3m space in the middle, I would like a manual wooden gate. Height of fence- 1.8m of palings with a plinth board taking total height to approx. 2m. - Due date: Flexible

Hi there, looking for someone to replace about 19m of fence between my neighbours and my property. Looking for someone to install and also discard the old fence.