Find a fence installation professional in Melbourne

Looking for a quote to build a new fence - it is about 15 - 18 m in length, with access available. Refer to second photo for the type of fence preferred (wooden is fine) - fence height 2 m required.

A friend has recently moved into a ground floor unit in Ascot Vale, and needs a rotting wooden fence (approx 2 metre width) demolished and replaced with Colorbond, with a gate in it for access. I've indicated the budget but do need quotes first. I have attached photos for ease of reference, one from the courtyard of the unit, and one from the other side of the fence, where the rubbish bins are. I have had the Colorbond quoted, and now need to get cracking with the the work! Cheers!

We removed part of the paling fence to build an ensuite on the side of our house. We now need a new paling fence put back with new materials, so supply and install. 8m long, 1.9m height. There is an existing fence on either side that it will need to be joined to. The gap between the ensuite and the fence is about 10 or 20 cm, so palings will need to be nailed from the other side. There is an old water tank that will be moved before you arrive.

Need a new boundary fence as old one falling down - looking to have it mesh style to allow vines etc to grow in it. 33m x 2m. Need old one removed too

Install 14 (1x1m) artificial green wall panels to a fence and a wall. https://m.youtube.com/watch?v=7Qq8ZgWOPmE Staple gun and masonry drill needed. Prep fence and wall with black landscaping fabric. Had wooden planks to fence to provide a flat surface.

Build 600mm trellis on top of 2m high boundary fencing, which is part brick wall and part galvanised iron with timber top. Length of trellis - 3 separate parts approx 17m in total. Trellis to be affixed to inside of existing boundary structures. Timber top part of existing boundary will need to be shaved so that it is levels. Materials not supplied

I’d like to get rid on my Eletrics gate. Add a new post to match the others add a swinging gate with a smart lock.

Fence posts have rotten and need replacing. Need some doors to be fixed too.

Replace a few fence pailings as pictured

Two dents in stainless steel panel on building facade. One ~15cm in length, and the other ~24cm in length. Cannot get behind panel, so will therefore likely be similar to refrigerator dent removal.

full height fence approx 2m long Abolish existing pine log posts & boards Install new posts and clad my side, leaving other side to neighbours garden ready for them to do what they want. A painted colour masonite board behind vertical timber battens on my side.

Replace shorter fence with taller fence. Modify post height to match. First pic is current, second pic is how it needs to look to mirror the other side

Supply, install and paint( 2 colours) picket fence including gate. Height of fence approximately 1m. Length of fence approximately 15m

- remove existing rear boundary fence - replace with new rear boundary fence approx 15 m wide by 2.4m high - take away all waste

Need a timber fence build 1.8m-2m high and 4.2m long . please quote with suggestions of a fence look and also with supply of materials

fence has horizontal paling and just deteriorated over the years. The palings on the top and bottom need replacing and they need stripping down and primed before the top coat. It has a remote control gate for entry into the carport.

Replace one half of our front timber fence ALL MATERIALS ARE SUPPLIED Remove existing Merbau pickets carefully to refit with twist nails. Remove 1 post and add 2 in Construct a new fence with a new gate (supplied) Dismantle and reassemble the existing front gate (twisted) Only apply if you had previes work in Airtasker or references

1.8m timber slat fence down side of house needs slats replacing. 15m long. Good access from both sides. Posts in Good condition except for 1.

Church side gate needs to be repaired so it can be self closing. Furthermore, we require a supply and install small 1.2m high metal gate as highlighted in the photo

Fix Back gate that is currently “sticking” at top (non hinge) side of gate. Suspect this is most likely due to slight movement of fence and gate. I believe the required fix is to (supply) and install an additional hinge near the top of the gate. Gate and fence are approx 2m high. Current hinges are rivet screws.