Find a local electronics repairer near you

I need an experienced painter/handyman to repaint marks on the walls in one bedroom. Room dimensions: Approximately 2.7m x 2.7m Wall height approximately 2.15m Scope of work: -Inspect walls and cornice -Clean and remove scuff marks where possible -Patch minor imperfections if required -Repaint affected areas and blend with existing colour -Leave area clean

IKEA METOD cabinets already assembled and installed. Need cover panels, fillers, kickboards and laminate benchtops installed. I have supplies but need the work.

Supply and installation of wall mounted outdoor hand rail covering 3 steps.

dig out tree stumps, move stumps to trailer. also could move dirt in wheelbarrow to skip bin if you are interested Type of gardening: Other Size of garden: Under 50m² Has green waste bin: Yes

Looking to get someone to close up all the gaps in my outdoor deck area. There are; 1) Small gaps between deck and wall 2) Larger gaps from around to deck alongside and back. Attached are photos -

Please comment what time you are available to complete today. Looking for someone to assemble a 4-in-1 multi game table NOW in Brighton

Need to have all the gaps filled in between the walls and skirting before painting

I left my scooter on all day and now the battery is flat. I need the scooter jump started.

Fill in the gaps between the gaps of the bricks

**BUDGET IS FINAL - DO NOT OFFER IF ABOVE WHAT IS SET PLEASE** Looking for an experienced painter available today in St Kilda. The job: Wall is prepped and ready. Original green has been sanded back, grey primer applied, and one coat of Dulux Vivid White and Snowy Mountain Half is already on. I need a professional to apply the final coat to a clean finish and correct any imperfections. Scope may also include: Touching up or repainting adjoining walls Ceiling work if needed Taping and masking Light sanding where required What's supplied: All paint (Dulux Vivid White + Snowy Mountain Half), drop sheets, and basic tools. Note: I'd suggest bringing your own quality roller and brushes as what I have is basic. Who I want: Someone who does clean, professional work and can get results today. Send a message with your availability and any relevant experience.

4 stumps: approx 30cm, 35cm, 40cm, 40cm diameter 2 stumps in front yard, 2 in backyard Easy access via side gate to backyard Standard residential block Looking to grind to below ground level Flexible on timing over the next couple of weeks

Storz & Bickel VEAZY - Dry Herb Vaporizer Looking for an experienced electronics hobbyist or bench technician with micro-soldering capabilities (fine-tip iron, flux, and ideally a microscope setup) to repair a high-end dry herb vaporizer. The Device & Materials:Model: Storz & Bickel VEAZY (a premium, German-engineered medical-grade device). Casing Material: The outer shell and internal structure are made of medical-grade PEEK plastic (Polyether ether ketone). This is a highly heat-resistant engineering polymer, but it is tightly sealed. It needs to be pried open gently with proper plastic opening tools without snapping the plastic tabs or melting the housing during solder work. The Issue:The device has an internal connection failure. I need a technician to open the PEEK casing, inspect the main logic board, and re-solder the broken joint. This is likely: Option A (If not charging): A fractured pin connection where the USB-C charging port meets the PCB board. Option B (If not turning on): A loose/snapped power wire connecting the single-button system or internal battery to the motherboard terminal pads. Important Note on Warranty:Please note that I am deliberately choosing to bypass the official manufacturer warranty process due to the long turnaround times for international shipping as well as not purchased in Australia. Because opening this device permanently voids my warranty coverage, I need someone meticulous who will treat the board with care, apply proper flux, and ensure there are no bridges or short circuits before re-assembling. Logistics:I can drop the device off to you if you are located around the Campsie / Inner West / Canterbury-Bankstown region, or you can here. Please offer your price based on a quick bench diagnostics and point-to-point micro-solder reflow.

We need to replace 2x bathroom basin taps that are constantly dripping / not shutting off. We have purchased replacements, just need someone to remove old and install new

I need the following services, 1. Identification of main calve. 2. 4 leaking taps to be fixed. Assessment and quotation for 1. Tap replacement 2. Plumbing arrangements required for a new dishwasher (currently there is no dishwasher and a new place to be created). 3. Bathroom grouting The posted budget and pictures are only for tap leak fix. For other tasks, an assessment is required.

Looking for handyman to put new table tops on these existing pole stands. 6 tables.

Assemble a desk and a wardrobe

Need to hang 3 pendant lights with shade, I have the lights and cords and shades. Change from Led downlights.

Need tree to be cut today or tomorrow. Also need the stumps to be removed

My car needs to be jumpstarted but is down the driveway so unable to use another car. Have tried a portable jumpstarter but isn’t working, not sure if the jumpstarter or the battery is the problem