Find trusted local electricians near you

I’m looking for an electrician to install 4x wall lights on the front of my weatherboard investment property in Mt Gravatt. See house photo attached. These are the lights… https://bitolalighting.com.au/product/havit-tivah-up-down-10w-led-tri-colour-outdoor-wall-pillar-lights/ (include the image of where the lights are to go + the existing house photo) Thanks, Diana

Electrician did some damage and I need it patched, small easy job.

Looking for someone to install a split system air-conditioner please

Water has killed the flame . There’s no hot water. Flame needs to be lit .

1x round led ceiling light to be installed Also need a pendant light inspected. Unsure how to remove the bulb

Job Description: I have a brand-new Airman SDG45SE-3B2N (approx. 37 kVA, 3-phase, standalone diesel generator) arriving in SA next week. I need a licensed electrician to install three 20A, 240V outlets, each on its own phase. This is stand-alone site power — NOT connecting into any building switchboard. Scope of Works Required: 1. Install Outlets Fit 3 × 20A, 240V single-phase outlets Clipsal 56 Series (round pin) One outlet per phase: Outlet 1 → L1 Outlet 2 → L2 Outlet 3 → L3 2. Protection Fit 20A RCBOs (1 per circuit) Generator has earth leakage relay, but each outlet requires its own RCBO. 3. Earthing Confirm MEN link inside generator Install earth stake (stand-alone generator on construction/remote sites) Confirm correct bonding and fault loop compliance 4. Testing Test & tag all circuits Provide a Certificate of Compliance (COC) Parts Required (Already Quoted by Supplier) Outlets & Enclosures (Clipsal / Uniquip): 3 × C01PHR320 – 20A 3-pin switched socket (Clipsal 56 series, round-pin) 3 × G4E – 4-module DIN enclosure 3 × CBC4PN – RCD/MCB cover for DIN modules Circuit Protection: (These are the correct units to use — CAPS’ 40A RCDs are not suitable.) 3 × 20A Type A 30mA RCBOs Hager ADN120T, OR Schneider / Clipsal MAX9 20A RCBO, OR Equivalent Earthing: Earth stake (galvanised) Earth clamp Earthing cable (16mm²) Others: Glands, lugs, ferrules, and suitable cable for 20A loads (You may supply the materials or I can supply them — either works.) Generator Info (For Sparkies): Airman SDG45SE-3B2N 37 kVA prime 3-phase 415 V Standard terminal layout: L1 / L2 / L3 / N / E Stand-alone generator only Loads are approx. 16–17A per circuit (resistive)

Ducted aircon - just one downstairs room has very weak airflow,

Setup & installing of this ceiling fan in our upstairs bedroom

Move switch in New location approximately half a metre and move light to centre of the room and look at ensuite power on the same circuit as slight switch

One of the Breakers won’t turn back on in the switchboard tried unplugging everything no luck, have all lights working but no power points working

Need to just replace a power point in the kitchen, if we can get this done tomorrow that would be great. Cheers

Hi, we've just replaced a hot water system and the old one is sitting at the front of the property It's a 315L Need someone to pickup and take it to a scrap yard

Need 2 x new PowerPoints added in loungeoom & study. Moving in today. Single story house

I need someone to go into my attic and replace 10 LED downlights with 10 new downlights. All downlights come with plugs. No wiring nor any other electrical works. Happy to supply the ladder and give a hand from ground level.

Replace one double powerpoint electrical socket. The buttons seem to get stuck while operating the socket. Please replace with appropriate electrical socket. New electrical socket should be on hand. Please post your best offer.

I need an electrician to put a power point in for a range hood or hard wire it into my kitchen and also fix a light on the ceiling.

I need a licensed electrician to replace my 2 x existing AC ceiling fans with new DC ceiling fans that I have already purchased. Scope of work: Remove existing AC ceiling fans (2) Install new DC ceiling fans (already onsite) (2) Remove existing fan speed regulators/dimmer switches Replace regulators with standard wall on/off switches. You have to provide this. (fans will be controlled by remote) Ensure constant power supply to DC fan receivers Make all wiring safe and compliant Test and confirm all fans are working correctly Requirements: Must be a Licensed Electrical Contractor Must provide a Certificate of Compliance / Electrical Safety Certificate upon completion for both fans Details: All fans and remotes are already onsite Ceiling height: standard residential Property type: residential house

Rough in 12 downlights and four switches 4 in bedroom (1 switch) 6 in open living (2 switches) 1 to operate kitchen and 1 to operate living. 2 in bathroom (1switch) I have cable on site

Remove old light and install new light