Find local ev charger installers near you

Tesla charger installation

Hi, I would like to install an EV charger in the garage of my house. I will supply the 7kW charger and I have 3-phase at home and a battery + solar panels system. The distance between the charger and the electricity meter board is about 10m but needs to go through the concrete slab floor.

Looking for electrician to connect 4 fans and a possible ev charge

I have power supply and EV charger ready, just need someone connect them together

I’m looking to install 11 or 22 KW wall charger.

I need to get a 7kW single phase EV charger installed in my garage. I already have the charger. House has 3 phase supply. Switchboard is in the garage and has couple of spare slots for the new 32 Amp circuit to be put on. Need to run around 2m of conduit on the wall from the switch-board to the charger install location (conduit can be run from behind the battery shown in the picture). Charger installation location is shown in red box in the attached pic. No special smart integration needs to be done between the charger and battery/inverter.

We currently have a EV charger point already wired in(it was operational for a few years.) we bought a new Tesla Wall connector and would like it to be wired in 3-phase. Conduit, isolators are all in place already. The house already has 3-phase power. Length from switchboard. Approximately, double garage length 5.4m across the top of the garage and about 1.6m down towards the isolator and 0.4m right angle bend towards the isolator Task involves new 3-phase circuit breaker Convert a line to 3-phase. Install charger to wall Wire in the charger.

I want to get my Tesla wall charger installed. The switchboard is on the other side of the house roughly 32m away.

I have a brand-new Geely 7kW Type 2 EV Home Wall Charger, which I will supply. My newly built house already has a dedicated EV charging outlet/connection installed in the garage by the builder. The EV circuit was installed as part of the original electrical installation and was confirmed by the builder/electrician at handover as being for EV charging. I am simply looking for a qualified/licensed electrician to connect the supplied Geely wall charger to the existing EV connection. Existing EV infrastructure The switchboard appears to have a dedicated EV circuit labelled “GARAGE N/L 15”, protected by a: Hager ADM432T RCBO 32A 3P+N (three-phase + neutral) 30mA Type A RCD protection 230–415V AC Hager's technical specifications confirm the ADM432T is a 4-pole, 3P+N, 32A Type A 30mA RCBO, which is consistent with the dedicated three-phase EV circuit installed at the property. The garage also has the dedicated EV connection/isolator already installed. Work required Please: 1. Inspect the existing EV connection and confirm it is suitable for the supplied Geely 7kW charger. 2. Connect and securely mount the Geely 7kW Type 2 wall charger to the existing EV circuit. 3. Reuse the existing EV circuit and protection — no new circuit is required unless you identify a compliance or capacity issue. 4. Test the installation and charger under load. 5. Confirm correct RCD/earthing operation. 6. Provide the required electrical compliance documentation/certificate on completion. I am not looking to have a new EV circuit installed. The house already has the EV infrastructure; I just need the supplied wall charger connected to it by a qualified electrician. Charger: Geely 7kW EV Home Wall Charger – Type 2 Customer supplies charger: Yes Existing EV outlet/circuit: Yes New circuit required: No — unless electrician determines existing installation is unsuitable after inspection Job: Connect, mount, test and certify.

need EV charger installed, single phase!

Looking for a licensed electrician in Fraser Rise to complete the following: * Supply and install 6 x downlights & a dimer switch * Supply and install 1 x new power point * Install my BYD 7kW single-phase EV charger I already have the BYD charger. Looking for everything else to be supplied and installed, including any required cabling, safety switch/RCBO and electrical certificate.

I have ev switch charger, 7kw single phase. How much will you charge? 10m cable run approx from switchboard to garage and need a breaker and isolator. Collingwood Park qld.

I’m looking for a licensed electrician to visit and assess a proposed EV charger installation on the pillar beside my parking space, then provide a written quote and documentation for strata approval. The charger needs to connect to my lot’s electricity meter so the electricity usage is billed to me. Important: The basement ceiling is high. A scissor lift or other elevated work platform may be needed during installation. Installation is out of scope for this assessment, but please take any access equipment requirements and costs into account when preparing the quote. After the assessment, please provide your licence number, proposed scope of work, confirmation that connection to my meter is feasible, and a certificate of currency for public liability insurance covering the works. This task is for assessment and documentation only. Installation can proceed only after strata approval, which is expected to take around one to two months.

I need a electrician to complete the wiring of my new and home EV charger and switch board, and isolator. Work required Connect the cable to the EV charger Connect the cable to the isolator switch Connect the cable into the switchboard Install the supplied breaker/switch in the switchboard.

I’m looking for a WA licensed electrician/electrical contractor with EV charger installation experience to install a MG 7kW Charge Hub Pro at my home in Willetton. Charger supplied by me - MG 7kW Charge Hub Pro - 7kW single-phase - Type 2 - 5m cable Existing setup - Existing residential switchboard as shown in attached photo - Property has solar installed - Existing main switch appears to be around 40A, but this must be verified onsite Scope of work - Inspect the existing switchboard and confirm whether it is suitable for a dedicated 7kW EV charger circuit - Confirm available supply capacity and phase loading - Supply and install a dedicated 32A circuit for the charger - Supply and install all required cable, conduit, breaker/RCBO, isolation and protection devices - Carry out any minor switchboard modifications reasonably required to make the installation compliant - Mount and connect the MG Charge Hub Pro - Test and commission the charger - Provide all required WA electrical compliance/certification documentation Important Please base your offer on a complete, compliant installation, including labour and standard materials. If inspection shows that a major switchboard upgrade, consumer mains upgrade, or other substantial additional work is required beyond a normal EV charger installation, please discuss this with me before carrying out that additional work. Please include with your offer - WA electrical licence / contractor details - EV charger installation experience - Confirmation that your price includes standard cable, conduit, breaker/RCBO, installation, testing and certification - Installation warranty - Earliest availability I can provide photos of the switchboard, proposed charger position and likely cable route before the job. Only licensed electricians able to certify the complete installation, please.

Installation of Tesla charger. It's a single storey house .tiled roof. Need the install in the Garage .

I've got a hone wall EV charger, would like to install it inside my garage. Property is part of a townhouse, but I have my own electrical box control point inside the garage so hopefully it's a straightforward process? I have the charger already, just need to install

Hi I have a fox EV charger Need to install closer to meter box 3 phase connection Area Campbelltown Thanks