Find experienced local carpenters in Blackburn South

To replace weatherboards. Owner will provide weatherboards. Carpenter / Handyman needs to provide appropriate nails.

Please see photos . Corner timber fascia has rotted away, needs replacement. Tasker to supply and install.

Refer attached picture for scope. Installation needed of pre-assembled cabinetry. Needs to be all put in the right spots, and end/side panels added along with kickers(supplied but may need to adjust) to make it all look built in. Installation of 2 floating vanities - 900mm wide, 1500mm wide Supply/installation of 18mm substrate over cabinetry as per diagram. Thanks

Scope of works in both bathrooms (see photos): 1) Framework - Frame 2 x bathroom niches - Install noggins for vanity, towel rails, toilet roll holders, hooks etc - Patch floor using yellow tongue flooring glue and nail down (so that sheeting goes on) 2) Install cavity slider doors. Both cavity frames appear to be ok. 1 door is available and 1 door is bowed. -replace bowed cavity slider door with new one -Clean out cavity slider pockets -Attach doors to sliding tracks -Check doors are working properly 3) Straighten walls - Plane/pack studs to make straight for sheeting both bathrooms tasker to supply all materials. Thanks

Refer attached pictures for cross referencing. The following non-structural walls timbers to be REMOVED (refer numbering labelled in RED). These walls will be stripped back and existing tiles/plaster removed, so all you need to do is to ensure any supporting timber that is left, is removed safely (to expose wall for resheeting/plastering). 2 - Entrance to master bedroom from hallway (0.9m wide x 2.1m tall) - enough for a new door /frame (refer requirement below under ''Addition of doors'' 3 - Linen cupboard (next to bedroom 2 / main bathroom on original plan) and wall either side of linen cupboard (measuring approx 1.6m wide in total) 4 - Wall against basin in main bathroom (approx 0.4m) 6 - Wall next to toilet in main bathroom (approx 0.9m wide) 7- Hallway wall to lead to study nook then main bathroom (approx 1m wide) The following walls (and 2 doors) to be ADDED, in readiness for resheeting/plastering (refer numbering labelled in GREEN): 1- Between WIR and hallway (approx 1m wide) 2 - Between front of linen cupboard location/bathroom and hallway (approx 1m wide) 3 -Between pantry and main bath 4 - For shower enclosure wall between main bath and pantry 5- Between study nook and kitchen/living area (approx 2.1m wide with 0.6m jut out to separate the space, and 2.7m height) 6 - Hollowcore door for laundry with jambs/materials/hinges/handle 7 - Hollowcore door for master bedroom with jambs/materials/hinges/handle Tasker to supply all materials including doors.

1. Remove approx. 3m of internal load bearing-wall, Temp propping/bracing 2. Supply and install 2 x 240 x 45 LVL beams in ceiling, including double studs (90x45 MGP10) in the frame to transfer weight onto (existing) stumps 3. Connect ceiling battens and struts to new beam 4. Frame bulkhead (as per picture) in readiness for plastering - 90cms depth (to suit future kitchen island underneath) Materials required (you to supply) - 2 x 240x45 LVL, Bulkhead timber, Double studs, Top and bottom plates, Noggins, Miscellaneous fixings. I can provide detailed engineering drawings. Building permit has been issued and once job is signed off, payment will be released. Thanks

Timber decking requiring surface preparation and staining or oiling. Approximately 32 m².

Replace rotten weatherboards and facias on house timber home. Quote needed

We’d like to have a custom cabinet built similar to the image attached. Needs to be constructed in weatherproof materials. Solid timber benchtop Caster wheels to allow it to be moved. Cupboards on either side, not drawers. We have the drinks fridge already.

Various wood repairs needed around the house due to rot: 1. Front door step & doorframe 2. Rear door step 3. Various small sections of weatherboard around the house 4. Front Window frame caulking & wood rot

Need a handyman carpenter to do a workbench. 6m by 0.7m with same length shelve underneath. Quote for supply and install please. See attached pics

Need to - replace rotten 1.8m x 3-5cm width pine wood (under plastic roof) - extend the width by adding additional pine wood 1.8m x 3-5cm (thickness) - add a new laser lite sheet 2.4m x 2.4m onto the wood Need labor effort only. Wood and the Laser lite sheet can be provided

Wooden Porch railing needs to be fixed.

Custom a reception desk for a hair salon

Our laundry cabinets have shelves under the bench top but we want to put a dryer in there. Bench top is the right height as we have a washer at one end. Would require cutting out some shelves & the base & top support & provably cutting some new wood to support the cabinets

There's a 150mm fire burn that spans across 3 pieces of timber and I need it repaired/fixed. This is located in the kitchen so is very visible so the finishing needs to exactly match the existing finishing.

We have a dinning of the width 190. We want to reduce it to 170

Building an insulation frame , adding insulation , building a plasterboard wall , rendering and painting walls and celing of 25 sqm garrage,

I have a Merbau Deck with an area of 41m2 including 2 small walls. Sand & Apply 2 coats of Deck Stain. Also Sand table top Due date: Needs to be done on Thursday, 30 November 2023 - Due date: Before Friday, 1 December 2023

Need help to reconfigure a kitchen bench top to run align against the wall. Job includes disassembly the bench top and install it again the wall to form a L shape work bench. - require skirting board, timber edge against the wall - we won’t need to disassemble the cabinet It would be ideal to get some help with the floor patching (only a small section - please refer to the photo). The flooring material will be supplied. Please contact me if you require more information. - Due date: Flexible