Find a reliable appliance technician in Broadmeadows VIC

I need help to fix my machine

My washing machine is showing tap water sign and is not working properly

Hi everyone, I’m looking for a licensed gas fitter to complete two items identified in my recent Gas Safety Check for a property in Broadmeadows (3047). The rangehood has already been replaced and certified, so only the gas-related items remain: 🔧 Work Required • Install PTR jacket on the hot water system (Fault code: G038) • Install gas isolation valve for the cooktop (Fault code: G034) These items are required to finalise gas safety compliance under the Residential Tenancies Regulations. 📄 I Can Provide • Full Gas Safety Check report • Photos • Fault codes and rectification notes 📍 Location Broadmeadows, VIC 📞 What I Need • A quote for the above work • Licensed gas fitter only as compliance certificate required Please comment below or message me directly if you can assist. Thanks in advance!

I have a Ryobi 2-stroke blower vac that starts and runs fine at high throttle, but it turns off when I release it from high throttle or when it idles. The engine will stay running as long as the throttle is fully engaged, but once it drops to low throttle/idle, it stalls. I have attempted to adjust the throttle/idle screw myself, but the issue persists. It’s possible I may not have adjusted it correctly, so I’m looking for someone experienced with small engines or 2-stroke equipment to properly diagnose and fix the issue.

I have caravan I need to fix the gas fitting and gas stove asap

Install Westinghouse WRR904SB (90cm slide-out, stainless steel trimmed front, model WRR904SB). Location: Under-cabinet recessed space (IKEA-style cabinetry). Measurements: Recess opening ~890 mm wide; available depth 300 mm; height clearance sufficient (product height 175 mm). Mounting: Slide-in under-cabinet fit (secure to cabinet sides/top/bottom with screws/clips; removable front fascia for integration if needed). Ducting: Rear venting required (no top space available). Hood has rear duct hole option (120 mm diameter outlet). Connect to existing angled rear vent path Install new WRR904SB (I will supply the unit). Connect rear ducting (Hood has rear duct hole option (120 mm diameter outlet). Connect to existing angled rear vent path (trapezoidal, narrowing to ~140 mm with 160/140 mm sides). Use 120 mm (or 125 mm with adapter) semi-rigid/rigid duct, short elbow/bend, clamps, and foil tape for airtight seal.) supply install ducting part or can purchase the required before install Power: to be connected by installer

I'm in need of someone to install my new washing machine and dryer.

The thermocouple on one Sabaf burner is not holding the valve open. Flame is normal but goes out when I release the knob. I think the thermocouple needs replacing.

Roller Shutter Winder Replacement Needed The manual roller shutter winder inside my room has stopped working. The internal cable/wire has snapped and the winder no longer rotates or lifts the shutter. I need someone to remove the old winder box and install a new one. Job includes: • Inspecting the current winder • Supplying and installing the correct replacement winder (crank/wire type) • Reconnecting the cable to the shutter drum • Making sure the shutter opens and closes smoothly Shutter is easily accessible. Located in Melbourne (Broadmeadows area). Looking for someone experienced with roller shutters.

Need help to connect a thermometer and light to a pizza oven

Hi, our garage door isn’t working properly — we currently have to open and close it manually. Could you please let me know how much it would cost to reset the remote so it operates automatically again?

Gas oven stopped working since few month

Existing continous gas hot water system is broken and needs to be replaced by new one. I have already got the new system (Rheem 20l ) and need some one to install this new system.

I need a plumber to install Meter at my place

Repaire commercial gas cook top and services

I have a gas leak near the meter, I contacted Ausnet who said to call a gas plumber, they switched off the gas at the meter because there is a leak. I need someone to go out and diagnose the leak and quote to fix it. I also have a gas ducted heating system, some vandals went under the floor boards and ripped off the heating pipes from the vents going inside. I'd also like a quote to clip them on again.

The hot water connection on my washing machine isn’t working. The cold water works fine, but hot water doesn’t seem to come through. Not sure if it’s a plumbing issue or something with the machine. Looking for someone experienced to inspect and fix the problem.

Yuan L. Please remake your offer we’re ready to go. Need three outdoor cameras installed at Broadmeadows house. Ideally need EZVIZ cameras - please quote your price for labour & cameras separately.

I have a Rinnai 20SF gas heater (natural gas) that lights up and runs for about a minute, then shuts off completely. • Pilot flame and burners ignite fine. • After a short time, it cuts out (likely thermocouple/flame sensor, gas valve magnet, or control board issue). • Unit is plugged in and fan runs.

Inner glass layer shattered during normal use of oven. I would like replacing only the door, as there's nothing wrong with the oven.